Craftsman YT 4500 To USE Cruise Control, System Characteristics, To Adjust Mower Cutting Height

Page 15

1.Start tractor and release parking brake.

2.Slowly depress forward (K) or reverse

(L)drive pedal to begin movement. Ground speed increases the further down the pedal is depressed.

TO USE CRUISE CONTROL

The cruise control feature can be used for

forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other condi- tions such as trimming at slow speeds may cause the cruise control to disen- gage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

With forward drive pedal depressed to desired speed, pull cruise control lever

(J)up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever (A) determines the cutting height.

Put attachment lift lever in desired cut-

ting height slot.

The cutting height range is approximate- ly 1" to 4". The heights are measured from the ground to the blade tip with the

engine not running. These heights are ap- proximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cutto approxi- mately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth. For best cutting performance, grass

over 6 inches in height should be mowed twice. Make the first cut rela-

tively high; the second to desired height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help

prevent scalping in most terrain condi- tions.

NOTE: Adjust gauge wheels with tractor on a flat level surface.

1.Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual).

2.With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appro- priate hole. Tighten securely.

3.Repeat for all, installing gauge wheel

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut with at- tachment lift lever.

2.Start mower blades by engaging at- tachment clutch control.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Craftsman Craftsman Limited Warranty TWO Years on Tractor Days on BatterySears, Roebuck and Co,, Noffman Estates, IL General Operation IV. Towing Service Safe Handling of GasolineGeneralservice PRODUCTSPECIFiCATiONS Sears Installation ServiceFor prices and additional information call Keys MowerTo Remove Tractor from Carton Unpack Carton Tools Required for AssemblyCheck Battery Adjust SeatAttach Mower Side Suspen First Install ANTI-SWAY BAR S10Turnsteeringwheeltopositionwheels Straightforward Check for Proper Position of ALL Belts ChecklistCheck Tire Pressure Check Deck LevelnessCruisecontrol @@@@@Tractor Attachment Clutch SwitchService Reminder / Hour ME= Know Your TractorTo SET Parking Brake StoppingTo USE Throttle Control D To USE Cruise Control System CharacteristicsTo Adjust Mower Cutting Height To Adjust Gauge WheelsTowing Carts and Other Attachments Using the Reverse Operation SystemTo Operate on Hills To TransportTo Start Engine Before Starting the EngineADD Gasoline Mowing TiPS Purge TRANSMiSSiONBefore Each USE Maintenance ScheduleChart General RecommendationsOperator Presence System TiresTo Change Engine OIL To Service CartridgeTransaxle Pump Fluid BeltsClean AIR Screen MufflerIN=LINE Fuel Filter Deck Washout Port To Remove Mower To Level Mower To Install MowerVisual SIDE-TO-SIDE Adjustment Precision SIDE-TO-SIDE AdjustmentTo Replace Motion Drive Belt Mower Drive Belt InstallationBelt Installation To Replace Mower Drive Belt Mower Drive Belt RemovalTo Attach Jumper Cables To Check BrakeTo Remove Wheel for Repairs To Start Engine with a Weak BAT TerySembly Replacing BatteryOther Fuel SystemEngine OiL CylindersHard to ProblemCause Correction StartExcessive Loss of powerWhen Operator WillDischarge Poor cut unevenCutting Mower blades willROS OFFSuggested Guide for Sighting Slopes for Safe Operation DOS Anos Para Tractores Pendientes FuncionamientoIV. Remolque Servioio MANIPULACI6N Segura DE LA GasoljnaOperacjones DE Servicjo Generales @@@@@ Acuerdos DE PROTECCI!N Para Especircaciones DEL ProductoResponsabimdades DEL Cmente DvertenciaLa segadora LlavesPara Hacer Rodar EL Tractor Dad y la funci6n de los controlesMonte Rueda Delatentera DE LA Fije LOS Brazos DE Suspension LAT Jnstale LA Segadora Y LA CorreaDE Transmisjon Montaje DE LA SE,GADORA Y DE LA COR- REA DE TransmisionRealiceelmismoprocedimientoelotro ladodeltractor DA DE Todas LAS Correas REVISI6N DE LA Presion DE LAS LlantasRevision DE LA Nivelacion DEL Conjunto Revision DE LA Posicion ADECUA=Fuego ESTRANGU- R/PIDO LentoLacion Atras Hacia Adelante Crucero DE Embrague Accesorio DELPage Para Usar EL Control DE LA ACELER- ACI6N D Parada Cuchillas DE LA SegadoraIMPULSI6N DE Recorrido MotorPara Operar LA Segadora Para Ajustar LAS Ruedas CAUBRA- DorasCorte Para Ajustar LA Altura DE Corte DE LA SegadoraCronometro Para TransportarRemolque DE Carretillas O Otros Accesorios Para Operar EN CerrosAntes DE Hacer Arrancar Para Hacer Arrancar EL MotorArranque CON Tjempo Templado Arranque CON Tiempo FrioCalentamiento Para LA Transmision Automatica Rgar LA TransmisjonConsejos Para Segar Programade Mantenimiento Recomendaciones GeneralesAntes DE Cada USO Vfrifiiz Sistema Presencia Operador TractorOperaoion DEL Freno LlantasPara Cambiar EL Aceite DEL Motor MotorEnfriamiento DEL Transeje Nivel DEL Fluido DE LA Bomba DEL TransejeSilenciador Filtro DE Combustible EN LineaLimpieza Limpieza DE LA Entrada DE AIRE/AREAS DE EnfriamentoPuerto CubiertaLejos Instalar LA S,EGADORA Y LA Correa Servicio O DE Hacer AjustesPara Desmontar LA Cortadora CuidadoAjuste DE Delante a Atras Para Nivelar LA SegadoraRegulacion Visual DE Lado a Lado REGULACI6N DE LA PRECISI6N DE LadoMontaje DE LA Correa DE LA SEGA- Dora Para Cambiar LA Correa DE IMPUL=SI6N DE Movimiento Desmontaje DE LA CorreaPara Verificar SI Funciona Bien EL Freno Impresion / Inclinacion DE LAS RUE=Entreoierre Y Reles Para Adjuntar LOS Cables DE EmpalmeReemplazar LA Bateria Para Cambiar LA Bombilla DE LA LUZ DelanteraCarburador MotorAceite DEL Motor CilindrosOtros EL Motor Identificacion DE ProblemasProblema Causa Correccion Estrangulacion ChokeIDENTIFICACI6N DE Problemas ProblemacausaCorreccjon Rapido Iproblema Causa CorreccionGUJASUGERiDAPARAMEDIR LAS Pendientes CON LA Vista Para UNA Our Home Your Home

YT 4500, 917.28990 specifications

The Craftsman 917.28990 YT 4500 is a robust lawn tractor that combines power and performance with comfort and ease of use, making it an ideal choice for homeowners with medium to large yards. With its impressive features and innovative technologies, this machine stands out in the competitive landscape of lawn care equipment.

At the heart of the Craftsman YT 4500 is a powerful 24 HP Kohler engine. This engine delivers reliable performance, ensuring that the tractor can tackle a variety of tasks from mowing to hauling and even towing. With a 42-inch cutting deck, the YT 4500 effectively maneuvers through tight corners and delivers a clean, professional-looking cut on your lawn.

One of the standout features of the Craftsman YT 4500 is its hydrostatic transmission, which provides effortless control and smooth operation. This technology allows users to change speed and direction easily without the need for constant gear shifting, enhancing the user experience, especially over extended periods of use.

The tractor also boasts a comfortable high-back seat with adjustable features, providing ample support during long mowing sessions. The ergonomically designed steering wheel allows for easy maneuverability, making it suitable for users of all sizes.

To improve efficiency, the YT 4500 is equipped with a cutting height adjustment feature, allowing users to select from multiple cutting heights to accommodate various grass types and conditions. This flexibility ensures optimal results year-round.

Additionally, the Craftsman 917.28990 includes a mulching feature, which finely chops grass clippings and returns them to the lawn as natural fertilizer, promoting a healthier lawn while reducing the need for bagging clippings. For those requiring extra versatility, the tractor is compatible with various attachments, including snow plows, baggers, and more, enabling year-round tasks.

Overall, the Craftsman 917.28990 YT 4500 is an excellent investment for any homeowner seeking reliability, comfort, and versatility in a lawn tractor. Its combination of power, advanced technologies, and thoughtful design ensures that lawn care can be both efficient and enjoyable. Whether you are tackling a simple mow or an extensive landscaping project, the YT 4500 proves to be a valuable addition to your outdoor equipment lineup.
Top Page Image Contents