Craftsman 917.27623 To Adjust Mower Cutting Height, To Operate Mower, To Stop Mower Blades

Page 15

1.Lower mower and adjust mower to de-

sired cutting height(See "TO ADJUST MOWER CUTTING HEIGHT" in this

section of manual).

2.Remove retainer spring and clevis pin which secure each gauge wheel bar.

3.Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

4.Replace retainer spring into clevis pin.

5.Be sure all gauge wheels are in the same setting.

IMPORTANT: Be sure to readjust gauge wheels if you change the cutting height of the mower deck.

Retainer

Spring

Clevis

Pin

TO ADJUST MOWER CUTTING HEIGHT

The cutting height is controlled by turning

the height adjustment knob in desired direction.

Turn knob clockwise (_) to raise cut- ting height.

Turn knob counterclockwise (_-_) to lower cutting height.

The cutting height range is approximately 1-1/2" to 4-1/2". The heights are mea- sured from the ground to the blade tip with the engine not running. These heights

are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

The average lawn should be cut to

approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut

relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut.

2.Lower mower with attachment lift con- trol.

3.Start mower blades by engaging at- tachment clutch control.

TO STOP MOWER BLADES -

disengage attachment clutch control.

_,CAUTION:

Do not operate the mower

without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

 

Attachment Lift Lever

Attachment Clutch

High Positi.

Switch Pull Out To

Low

"Engage"

,SPosition

 

//'

 

Deflector

 

Shield

Push In To

 

"Disengage"

 

REVERSE OPERATION SYSTEM (ROS) Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direc- tion with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

_WARNING: Backing up with the at- tachment clutch engaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

15

Image 15
Contents Criiftsmiih Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceII1. Children IV, TowingGeneral Service Customer Responsibilities Sears Installation ServiceJJJ Steering WheelBefore Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyCheck Battery Unpack CartonInstall Seat Attach Front Plate Connect Rear PinsInstall Mower and Drive Belt Assemble Gauge Wheels to Mower DeckFor PositionALL Belts Property damage Tractor HOW USE Your Tractor To SET Parking BrakeStopping To Adjust Mower Cutting Height To Operate MowerTo Stop Mower Blades ADD Gasoline To TransportTowing Carts and Other ATTACH- Ments Before Starting the Engine Check Engine OIL LevelMowing Tips To Start EngineGeneral Recommendations Lubrication ChartBlade Removal TiresOperator Presence System Reverse Operation System ROS Blade CareChecktransaxle OIL Level BatteryAIR Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL FilterTo Remove Mower Vice or AdjustmentsTo Install Mower TractorEqual in Length To Level Mower HousingSIDE-TO-SIDE Adjustment Both Front Plate Links Must beMower Drive Belt Installation To Replace Mower Drive BeltMower Drive Belt Removal To Adjust Attachment Clutch To Check and Adjust BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs To Adjust Steering Wheel Align MentReplacing Battery To Start Engine with a Weak BAT TeryTo Replace Headlight Bulb EngineTo Remove Hood and Grill AS Sembly Final Setting To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingOther Fuel SystemEngine OIL CylindersProblem CauseStart Engine Problem Cause Correction TroubleshootingchartOFF Problem Cause CorrectionTractor - Model Number SchematicElectrical Part Description Tractor - Model Number 917,276230 Chassis and Enclosures Part Tractor - Model Number 917,276230 Ground Drive KEY Part Description Tractor - Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. no KEY Part Tractor - Model Number 917,276230Tractor - Model Number Seat Assembly KEYKEY Part Description Wheels &TIRES DecalsKEY Part Lift AssemblyAcop v,.,v Tractor - Model Number Mower Deck Transaxle Dimensions Given U.S. inches @/18 HEAD/VALVE/BREATHER Crankcase IGNITION/ELECTRICAL AIR INTAKE/FILTRATION Not IllustratedOIL PAN / Lubrication J Starting System KEY Part Description OIL PAN/LUBRICATION Fuel Systemj Crankshaft KEY Part Description Exhaust KEY Part DescriptionFuel System KEY Part NO. NO. Description Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Our Home

917.27623 specifications

The Craftsman 917.27623 is a versatile and robust lawn tractor designed to make lawn maintenance efficient and enjoyable. With its user-friendly features and advanced technologies, this machine enhances the mowing experience for homeowners and lawn care enthusiasts alike.

One of the standout features of the Craftsman 917.27623 is its powerful 24-horsepower Briggs & Stratton engine. This reliable engine provides ample power, facilitating smooth operation even during challenging mowing conditions. The engine is paired with a smooth hydrostatic transmission, which allows for effortless speed adjustments and greater control, making it easy to navigate around tight corners and obstacles in the yard.

The mower is equipped with a generous 46-inch cutting deck. This size strikes an ideal balance between maneuverability and cutting efficiency, allowing users to tackle medium to large yards in less time. The deck also features a three-blade system, ensuring that grass is cut evenly and cleanly, promoting overall lawn health. Moreover, the cutting height can be easily adjusted with a simple lever, offering users the flexibility to maintain their lawns at different heights based on personal preference and seasonal needs.

In terms of durability, the Craftsman 917.27623 boasts a robust steel frame that can withstand the rigors of regular lawn maintenance. The materials used in its construction are designed to resist rust and corrosion, enhancing the lifespan of the mower.

Ergonomics play a key role in the design of the Craftsman 917.27623. The tractor features a comfortable high-back seat that reduces fatigue during extended use. Additionally, the dual-lever steering provides enhanced maneuverability, making it easy to steer the mower in tight spaces or around landscaping features.

Another significant technology integrated into this mower is its mulching capability. By utilizing the optional mulching kit, users can finely chop grass clippings, allowing them to decompose and return nutrients to the lawn. This promotes a healthier lawn and reduces the need for additional fertilization.

Overall, the Craftsman 917.27623 stands out for its powerful performance, user-friendly features, and durability. With its optimal cutting system and thoughtful design, it serves as an excellent addition to any homeowner's lawn care arsenal, transforming the often mundane chore of mowing into a more pleasant and efficient task.