Craftsman 917.27623 To Replace Headlight Bulb, Engine, To Remove Hood and Grill AS Sembly

Page 27

4.Install new batterywith terminalsin same positionas old battery.

5.Reinstallterminalguard.

6.First connectRED batterycableto positive(+) batteryterminalwith hex bolt and kepsnut as shown.Tighten securely.

7.ConnectBLACKgroundingcableto negative(-) batteryterminalwith re- maininghex bolt and keps nut.Tighten securely

8.Closeterminalaccess doors.

9.Closehood.

Hood

Headlight Wire Connector

KepsNut___

 

Terminaly

_>_

exBolt

Access_

"

Door .

_'_----

Positive(Red)

Guard

_

"Negative(Black)

 

............

Cable

TO REPLACE HEADLIGHT BULB

1.Raise hood.

2.Pull bulb holder out of the hole in the backside of the grill.

3.Replace bulb in holder and push bulb holder securely back into the hole in

the backside of the grill.

4.Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause

your tractor to run poorly, stop running, or prevent it from starting.

• Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers ex- pense, may be performed by any non-road

engine repair establishment or individual. Warranty repairs must be performed by an

authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

1.With engine not running, move throttle control lever to fast position.

2.Check that speed control lever is against stop screw. If it is not, loosen casing clamp screw and pull throttle cable until lever is against screw. Tighten clamp screw securely.

Idle Fuel Adjusting

Idle Speed

Needle (If Equipped)

Ad usting Screw

 

TO REMOVE HOOD AND GRILL AS-

SEMBLY

1.Raise hood.

2.Unsnap headlight wire connector.

3.Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

4.When replacing hood, be sure to re- connect the headlight wire connector.

Stop

Screw

27 Clamp Screw

Throttle

Control

Cable

Choke

Control

Image 27
Contents Criiftsmiih Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceII1. Children IV, TowingGeneral Service Customer Responsibilities Sears Installation ServiceJJJ Steering WheelBefore Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyCheck Battery Unpack CartonInstall Seat Attach Front Plate Connect Rear PinsInstall Mower and Drive Belt Assemble Gauge Wheels to Mower DeckFor PositionALL Belts Property damage Tractor HOW USE Your Tractor To SET Parking BrakeStopping To Adjust Mower Cutting Height To Operate MowerTo Stop Mower Blades ADD Gasoline To TransportTowing Carts and Other ATTACH- Ments Before Starting the Engine Check Engine OIL LevelMowing Tips To Start EngineGeneral Recommendations Lubrication ChartBlade Removal TiresOperator Presence System Reverse Operation System ROS Blade CareChecktransaxle OIL Level BatteryAIR Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL FilterTo Remove Mower Vice or AdjustmentsTo Install Mower TractorEqual in Length To Level Mower HousingSIDE-TO-SIDE Adjustment Both Front Plate Links Must beMower Drive Belt Installation To Replace Mower Drive BeltMower Drive Belt Removal To Adjust Attachment Clutch To Check and Adjust BrakeTo Replace Motion Drive Belt To Remove Wheel for Repairs To Adjust Steering Wheel Align MentReplacing Battery To Start Engine with a Weak BAT TeryTo Replace Headlight Bulb EngineTo Remove Hood and Grill AS Sembly Final Setting To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingOther Fuel SystemEngine OIL CylindersProblem CauseStart Engine Problem Cause Correction TroubleshootingchartOFF Problem Cause CorrectionTractor - Model Number SchematicElectrical Part Description Tractor - Model Number 917,276230 Chassis and Enclosures Part Tractor - Model Number 917,276230 Ground Drive KEY Part Description Tractor - Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. no KEY Part Tractor - Model Number 917,276230Tractor - Model Number Seat Assembly KEYKEY Part Description Wheels &TIRES DecalsKEY Part Lift AssemblyAcop v,.,v Tractor - Model Number Mower Deck Transaxle Dimensions Given U.S. inches @/18 HEAD/VALVE/BREATHER Crankcase IGNITION/ELECTRICAL AIR INTAKE/FILTRATION Not IllustratedOIL PAN / Lubrication J Starting System KEY Part Description OIL PAN/LUBRICATION Fuel Systemj Crankshaft KEY Part Description Exhaust KEY Part DescriptionFuel System KEY Part NO. NO. Description Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Our Home

917.27623 specifications

The Craftsman 917.27623 is a versatile and robust lawn tractor designed to make lawn maintenance efficient and enjoyable. With its user-friendly features and advanced technologies, this machine enhances the mowing experience for homeowners and lawn care enthusiasts alike.

One of the standout features of the Craftsman 917.27623 is its powerful 24-horsepower Briggs & Stratton engine. This reliable engine provides ample power, facilitating smooth operation even during challenging mowing conditions. The engine is paired with a smooth hydrostatic transmission, which allows for effortless speed adjustments and greater control, making it easy to navigate around tight corners and obstacles in the yard.

The mower is equipped with a generous 46-inch cutting deck. This size strikes an ideal balance between maneuverability and cutting efficiency, allowing users to tackle medium to large yards in less time. The deck also features a three-blade system, ensuring that grass is cut evenly and cleanly, promoting overall lawn health. Moreover, the cutting height can be easily adjusted with a simple lever, offering users the flexibility to maintain their lawns at different heights based on personal preference and seasonal needs.

In terms of durability, the Craftsman 917.27623 boasts a robust steel frame that can withstand the rigors of regular lawn maintenance. The materials used in its construction are designed to resist rust and corrosion, enhancing the lifespan of the mower.

Ergonomics play a key role in the design of the Craftsman 917.27623. The tractor features a comfortable high-back seat that reduces fatigue during extended use. Additionally, the dual-lever steering provides enhanced maneuverability, making it easy to steer the mower in tight spaces or around landscaping features.

Another significant technology integrated into this mower is its mulching capability. By utilizing the optional mulching kit, users can finely chop grass clippings, allowing them to decompose and return nutrients to the lawn. This promotes a healthier lawn and reduces the need for additional fertilization.

Overall, the Craftsman 917.27623 stands out for its powerful performance, user-friendly features, and durability. With its optimal cutting system and thoughtful design, it serves as an excellent addition to any homeowner's lawn care arsenal, transforming the often mundane chore of mowing into a more pleasant and efficient task.