Craftsman 917.27623 owner manual To Level Mower Housing, SIDE-TO-SIDE Adjustment, Equal in Length

Page 23

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See "PRODUCT

SPECIFICATIONS" section of this manual).

If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

•Raise mower to its highest position.

•Measure height from bottom edge of mower to ground level at front corners

of mower. Distance "A" on both sides of mower should be the same.

•If adjustment is necessary, make adjust- ment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

• Recheck measurements after adjusting.

Bottom

Edge of

Bottom Edge of

Mower

to Ground

Mower to Ground

Check adjustment on right side of tractor. Position any blade so the tip is pointing straight forward. Measure distance "B" at front and rear tip of blade

•Before making any necessary adjust- ments, check that both front plate links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of blade, loosen nut "C"

on both front links an equal number of turns.

NOTE: Each full turn of nut "C" will

change distance "B" by approximately 3/16".

•When distance "B" is 1/8" to 1/2" lower

at front than rear, tighten nut "D" against trunnion on both front links.

•To raise front of blade, loosen nut "D" from trunnion on both front links.

Tighten nut "C" on both front links an equal number of turns. The two front

links must remain equal in length.

•When distance "B" is 1/8" to 1/2" lower

at front than rear, tighten nut "D" against trunnion on both front links.

•Recheck side-to-side adjustment.

q_.':'o\X I oo/Blade

Suspension

Arm

Eift Link

ustment

Nut

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to- side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is approximately 1/8" to 1/2" lower than the rear tip when the mower is in its

,_ghest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

BOTH FRONT PLATE LINKS MUST BE

EQUAL IN LENGTH

Nut

7

Front Plate Trunnion

Assembly

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Criiftsmiih Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Safe Handling of Gasoline ServiceII1. Children IV, TowingGeneral Service Customer Responsibilities Sears Installation ServiceJJJ Steering WheelBefore Removing Tractor from Skid Attach Steering Wheel Tools Required for AssemblyCheck Battery Unpack CartonInstall Seat Attach Front Plate Connect Rear PinsInstall Mower and Drive Belt Assemble Gauge Wheels to Mower DeckALL Belts ForPosition Property damage Tractor Stopping HOW USE Your TractorTo SET Parking Brake To Stop Mower Blades To Adjust Mower Cutting HeightTo Operate Mower ADD Gasoline To TransportTowing Carts and Other ATTACH- Ments Before Starting the Engine Check Engine OIL LevelMowing Tips To Start EngineGeneral Recommendations Lubrication ChartBlade Removal TiresOperator Presence System Reverse Operation System ROS Blade CareChecktransaxle OIL Level BatteryAIR Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas Engine OIL FilterTo Remove Mower Vice or AdjustmentsTo Install Mower TractorEqual in Length To Level Mower HousingSIDE-TO-SIDE Adjustment Both Front Plate Links Must beMower Drive Belt Removal Mower Drive Belt InstallationTo Replace Mower Drive Belt To Replace Motion Drive Belt To Adjust Attachment ClutchTo Check and Adjust Brake To Remove Wheel for Repairs To Adjust Steering Wheel Align MentReplacing Battery To Start Engine with a Weak BAT TeryTo Remove Hood and Grill AS Sembly To Replace Headlight BulbEngine Final Setting To Adjust Choke ControlTo Adjust Carburetor Preliminary SettingOther Fuel SystemEngine OIL CylindersStart Engine ProblemCause Problem Cause Correction TroubleshootingchartOFF Problem Cause CorrectionTractor - Model Number SchematicElectrical Part Description Tractor - Model Number 917,276230 Chassis and Enclosures Part Tractor - Model Number 917,276230 Ground Drive KEY Part Description Tractor - Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. no KEY Part Tractor - Model Number 917,276230KEY Part Description Tractor - Model Number Seat AssemblyKEY Wheels &TIRES DecalsKEY Part Lift AssemblyAcop v,.,v Tractor - Model Number Mower Deck Transaxle Dimensions Given U.S. inches @/18 HEAD/VALVE/BREATHER Crankcase IGNITION/ELECTRICAL AIR INTAKE/FILTRATION Not IllustratedOIL PAN / Lubrication J Starting System KEY Part Description OIL PAN/LUBRICATION Fuel Systemj Fuel System KEY Part NO. NO. Description Crankshaft KEY Part DescriptionExhaust KEY Part Description Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Our Home

917.27623 specifications

The Craftsman 917.27623 is a versatile and robust lawn tractor designed to make lawn maintenance efficient and enjoyable. With its user-friendly features and advanced technologies, this machine enhances the mowing experience for homeowners and lawn care enthusiasts alike.

One of the standout features of the Craftsman 917.27623 is its powerful 24-horsepower Briggs & Stratton engine. This reliable engine provides ample power, facilitating smooth operation even during challenging mowing conditions. The engine is paired with a smooth hydrostatic transmission, which allows for effortless speed adjustments and greater control, making it easy to navigate around tight corners and obstacles in the yard.

The mower is equipped with a generous 46-inch cutting deck. This size strikes an ideal balance between maneuverability and cutting efficiency, allowing users to tackle medium to large yards in less time. The deck also features a three-blade system, ensuring that grass is cut evenly and cleanly, promoting overall lawn health. Moreover, the cutting height can be easily adjusted with a simple lever, offering users the flexibility to maintain their lawns at different heights based on personal preference and seasonal needs.

In terms of durability, the Craftsman 917.27623 boasts a robust steel frame that can withstand the rigors of regular lawn maintenance. The materials used in its construction are designed to resist rust and corrosion, enhancing the lifespan of the mower.

Ergonomics play a key role in the design of the Craftsman 917.27623. The tractor features a comfortable high-back seat that reduces fatigue during extended use. Additionally, the dual-lever steering provides enhanced maneuverability, making it easy to steer the mower in tight spaces or around landscaping features.

Another significant technology integrated into this mower is its mulching capability. By utilizing the optional mulching kit, users can finely chop grass clippings, allowing them to decompose and return nutrients to the lawn. This promotes a healthier lawn and reduces the need for additional fertilization.

Overall, the Craftsman 917.27623 stands out for its powerful performance, user-friendly features, and durability. With its optimal cutting system and thoughtful design, it serves as an excellent addition to any homeowner's lawn care arsenal, transforming the often mundane chore of mowing into a more pleasant and efficient task.
Top Page Image Contents