Craftsman 917.27623 owner manual Install Seat

Page 9

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4.Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

5.Pivot seat and pan forward and as- semble adjustment knob and flat washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat.

7.Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

8.Get off seat without moving its ad- justed position.

9.Raise seat and tighten adjustment knob securely.

Seat

Seat

Bolt

Flat Washer

\

Adj

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

1.Press lift lever plunger and raise

attachment lift lever to its highest po- sition.

2.Release parking brake by depressing clutch/brake pedal.

3.Place gearshift lever in neutral (N) position.

4.Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Operation section for location and

function of controls)

_WARNING: Before starting, read, un- derstand and follow all instructions in the

Operation section of this manual. Be sure

tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Sit on seat in operating position,

depress clutch/brake pedal and set the parking brake.

4.Place gear shift lever in neutral (N) position.

5.Press lift lever plunger and raise

attachment lift lever to its highest posi- tion.

6.Start the engine. After engine has started, move throttle control to idle position.

7.Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

8.Slowly release clutch/brake pedal and slowly drive tractor off skid.

9.Apply brake to stop tractor, set park- ing brake and place gearshift lever in neutral position.

10.Turn ignition key to "STOP" position. Continue with the instructions that follow.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Criiftsmiih Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation II1. Children ServiceIV, Towing Safe Handling of GasolineGeneral Service Customer Responsibilities Sears Installation ServiceJJJ Steering WheelCheck Battery Tools Required for AssemblyUnpack Carton Before Removing Tractor from Skid Attach Steering WheelInstall Seat Install Mower and Drive Belt Connect Rear PinsAssemble Gauge Wheels to Mower Deck Attach Front PlateFor PositionALL Belts Property damage Tractor HOW USE Your Tractor To SET Parking BrakeStopping To Adjust Mower Cutting Height To Operate MowerTo Stop Mower Blades Towing Carts and Other ATTACH- Ments To TransportBefore Starting the Engine Check Engine OIL Level ADD GasolineMowing Tips To Start EngineGeneral Recommendations Lubrication ChartOperator Presence System Reverse Operation System ROS TiresBlade Care Blade RemovalChecktransaxle OIL Level BatteryClean AIR INTAKE/COOLING Areas Clean AIR ScreenEngine OIL Filter AIR FilterTo Install Mower Vice or AdjustmentsTractor To Remove MowerSIDE-TO-SIDE Adjustment To Level Mower HousingBoth Front Plate Links Must be Equal in LengthMower Drive Belt Installation To Replace Mower Drive BeltMower Drive Belt Removal To Adjust Attachment Clutch To Check and Adjust BrakeTo Replace Motion Drive Belt Replacing Battery To Adjust Steering Wheel Align MentTo Start Engine with a Weak BAT Tery To Remove Wheel for RepairsTo Replace Headlight Bulb EngineTo Remove Hood and Grill AS Sembly To Adjust Carburetor To Adjust Choke ControlPreliminary Setting Final SettingEngine OIL Fuel SystemCylinders OtherProblem CauseStart Engine Problem Cause Correction TroubleshootingchartOFF Problem Cause CorrectionTractor - Model Number SchematicElectrical Part Description Tractor - Model Number 917,276230 Chassis and Enclosures Part Tractor - Model Number 917,276230 Ground Drive KEY Part Description Tractor - Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. no KEY Part Tractor - Model Number 917,276230Tractor - Model Number Seat Assembly KEYKEY Part Description Wheels &TIRES DecalsKEY Part Lift AssemblyAcop v,.,v Tractor - Model Number Mower Deck Transaxle Dimensions Given U.S. inches @/18 HEAD/VALVE/BREATHER Crankcase IGNITION/ELECTRICAL AIR INTAKE/FILTRATION Not IllustratedOIL PAN / Lubrication J Starting System KEY Part Description OIL PAN/LUBRICATION Fuel Systemj Crankshaft KEY Part Description Exhaust KEY Part DescriptionFuel System KEY Part NO. NO. Description Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationPage Our Home

917.27623 specifications

The Craftsman 917.27623 is a versatile and robust lawn tractor designed to make lawn maintenance efficient and enjoyable. With its user-friendly features and advanced technologies, this machine enhances the mowing experience for homeowners and lawn care enthusiasts alike.

One of the standout features of the Craftsman 917.27623 is its powerful 24-horsepower Briggs & Stratton engine. This reliable engine provides ample power, facilitating smooth operation even during challenging mowing conditions. The engine is paired with a smooth hydrostatic transmission, which allows for effortless speed adjustments and greater control, making it easy to navigate around tight corners and obstacles in the yard.

The mower is equipped with a generous 46-inch cutting deck. This size strikes an ideal balance between maneuverability and cutting efficiency, allowing users to tackle medium to large yards in less time. The deck also features a three-blade system, ensuring that grass is cut evenly and cleanly, promoting overall lawn health. Moreover, the cutting height can be easily adjusted with a simple lever, offering users the flexibility to maintain their lawns at different heights based on personal preference and seasonal needs.

In terms of durability, the Craftsman 917.27623 boasts a robust steel frame that can withstand the rigors of regular lawn maintenance. The materials used in its construction are designed to resist rust and corrosion, enhancing the lifespan of the mower.

Ergonomics play a key role in the design of the Craftsman 917.27623. The tractor features a comfortable high-back seat that reduces fatigue during extended use. Additionally, the dual-lever steering provides enhanced maneuverability, making it easy to steer the mower in tight spaces or around landscaping features.

Another significant technology integrated into this mower is its mulching capability. By utilizing the optional mulching kit, users can finely chop grass clippings, allowing them to decompose and return nutrients to the lawn. This promotes a healthier lawn and reduces the need for additional fertilization.

Overall, the Craftsman 917.27623 stands out for its powerful performance, user-friendly features, and durability. With its optimal cutting system and thoughtful design, it serves as an excellent addition to any homeowner's lawn care arsenal, transforming the often mundane chore of mowing into a more pleasant and efficient task.
Top Page Image Contents