Craftsman 917.27384 owner manual Tractor, To Remove Mower, To Install Mower

Page 22

WARNING:VICE OR ADJUSTMENTS:TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER-

1.Depress clutch/brake pedal fully and set parking brake.

2.Place motion control lever in neutral (N) position.

3.Place attachment clutch in "DISENGAGED" position.

4.Turn ignition key to "STOP" and remove key.

5.Make sure the blades and all moving parts have completely stopped.

6.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the right side of tractor.

1.Place attachment clutch in "DISEN- GAGED" position.

2.Move attachment lift lever forward to lower mower to its lowest position.

3.Roll belt off engine pulley.

4.Remove small retainer spring, and remove clutch spring off pulley bolt.

5.Remove large retainer spring, slide

collar off and push housing guide out of bracket.

6.Disconnect anti-sway bar from chassis bracket by removing retainer spring.

7.Disconnect suspension arms from rear deck brackets by removing retainer springs.

8.Disconnect front links from deck by removing retainer springs.

9.Raise lift lever to raise suspension arms. Slide mower out from under trac- tor.

Clutch Spring

Small Retainer Spring

Retainer Spring

Anti-Sway

Collar ._.

Large

HousingRetainer

Spring Bracket

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer

springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer

spring.

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

• ..

_

,'__

_.._. _.'

•Flat

-

_"_.+- _:-

 

.-

_<_;_"_"1"_ Square Hole

Retainer Springs

(Both Sides)

Deflector Shield

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Jcriiftsmrnj Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryII. Slope Operation General OperationDo not IV. ServiceIII. Children Across Customer Responsibilities Product SpecificationsSears Installation Service Repair Protection AgreementsSteering Wheel Slope SheetCheck Battery Howto SET UP Your TractorTools Required for Assembly To Remove Tractor fromInstall Seat Assemble Gauge Wheels to Mower DeckCheck for Proper Position of ALL Belts Install Mulcher PlateCheck Deck Levelness Check Brake SystemAutomatic Models only Attachment Clutch Lever Used Know Your TractorLift Lever Plunger Used to release To SET Parking Brake HOW to USE Your TractorTo Adjust Mower Cutting Height To Move Forward and BackwardTo Operate On Hills To Adjust Gauge WheelsTo Operate Mower Do not drive up or downTransmission Engaged Transmission Disengaged Before Starting the EngineTo Start Engine MentsAutomatic Transmission Warm UP Purge TransmissionMowing Tips Mulching Mowing TipsBefore Each USE Lubrication ChartGeneral Recommendations Check tire pressureBlade Removal BatteryTractor To Sharpen BladeTransaxle Pump Fluid EngineLubrication Cleaning Clean AIR INTAKE/COOLING AreasClean AIR Screen AIR FilterTractor To Install MowerTo Remove Mower To Replace Mower Blade Drive Belt To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake To Check and Adjust BrakeTo Replace Motion Drive Belt Front Wheel TOE-IN/CAMBER Transaxle Motion Control Lever Neutral AdjustmentTransmission Removal Replacement To Remove Wheel for RepairsTo Attach Jumper Cables Replacing BatteryTo Remove CABLES, Reverse Order To Replace Headlight Bulb To Adjustthrottle Control CableEngine Acceleration Test Engine OIL BatteryFuel System CylindersIgnition switch Troubleshooting ChartCause Correction Problem Cause Problem Cause Correction Tractor - Model Number Schematic AMETdLUTCHTractor - Model Number ElectricalTractor - Model Number Electrical KEY Part DescriptionTractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number Ground Drive 25/32 Tractor - Model Number 917.273840 Steering Assembly Tractor - Model Number 917.273840 Steeringassembly Tractor - Model Number Engine Control Throttle/ChokeTractor - Model Number Seat Assembly KEY PartTractor - Model Number Decals DescriptionTractor - Model Number Lift Assembly Link FrontTractor - Model Number Mower Deck 177563 Bracket, Deflector 124 351 64 \ 125 107 900 Ill 625 Cylinder HEAD, Valve and Breather Crankcase Headnalvbreathercrankcase Iiiiiiiiiiiiiiiiiii Not Illustrated Starting System OIL PAN/LUBRICATION OIL PAN/LUBRICATION KEY Part NO. no Iliiii 77% Crankshaft Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.27384 specifications

The Craftsman 917.27384 is a powerful lawn tractor designed to deliver both efficiency and versatility for homeowners who strive for a pristine lawn. Known for its robust construction and functional design, this model is particularly favored for its ability to tackle various lawn care tasks with ease, making it an essential tool for anyone maintaining a sizeable outdoor area.

One of the standout features of the Craftsman 917.27384 is its strong engine performance. It is typically powered by a reliable and efficient 19.5 HP Briggs & Stratton engine, designed to provide ample power to handle tough mowing conditions. This reliable engine ensures smooth operation and longevity, helping users complete their mowing tasks without interruptions for maintenance or repairs.

Another notable characteristic is its cutting deck. The Craftsman 917.27384 comes equipped with a 42-inch cutting deck, which allows for efficient mowing by covering a wide area with each pass. The deck is designed with multiple height adjustment options, providing flexibility to adapt to various grass types and desired cutting lengths. This feature not only enhances the overall appearance of your lawn but also promotes healthy grass growth.

Additionally, this lawn tractor boasts several user-friendly technologies that enhance the mowing experience. The model features a foot-controlled hydrostatic transmission, allowing for smooth acceleration and deceleration without the need for shifting gears. This is particularly beneficial for navigating around obstacles and adjusting speed quickly as needed.

Comfort is another important aspect of the Craftsman 917.27384. It is designed with an ergonomic seat and easy-to-reach controls, ensuring that operators can mow comfortably for extended periods. The 917.27384 also includes a large fuel tank that minimizes refueling frequency, ensuring that users can complete larger jobs without interruption.

In terms of maintenance, the Craftsman lawn tractor is user-friendly, featuring easily accessible components for routine checks and servicing. This attention to detail makes it simple for homeowners to keep the tractor in optimal condition over the years.

Overall, the Craftsman 917.27384 combines power, ease of use, and comfort, making it an excellent choice for homeowners seeking a reliable lawn tractor capable of delivering impressive results. Whether you are mowing, bagging, or mulching, this model is designed to meet diverse lawn care needs effectively.
Top Page Image Contents