Craftsman 917.27384 Transaxle Motion Control Lever Neutral Adjustment, Front Wheel TOE-IN/CAMBER

Page 25

Engine Pulley ----- z_

Clutching Idler

Stationary Idler /

Center Span

Keeper

Transmission

Input Pulley 0

TRANSAXLE MOTION CONTROL

LEVER NEUTRAL ADJUSTMENT

The motion control lever has been preset at the factory and adjustment should not be necessary.

1.Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

2.Start engine and move motion con- trol lever until tractor does not move forward or backward.

3.Hold motion control lever in that posi- tion and turn engine off.

4.While holding motion control lever in place, loosen the adjustment bolt.

5.Move motion control lever to the neu- tral (N) (lock gate) position.

6.Tighten adjustment bolt securely. NOTE: If additional clearance is needed

to get to adjustment bolt, move mower deck height to the lowest position. After above adjustment is made, if the

tractor still creeps forward or backward while motion control lever is in neutral

position, follow these steps:

1.Loosen the adjustment bolt.

2.Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

3.Tighten adjustment bolt securely.

4.Start engine and test.

5.If tractor still creeps, repeat above steps until satisfied.

Motion Control Lever

Neutral

Adjustment Bolt

TRANSMISSION REMOVAL/

REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged

after reinstallation and before operating the tractor. See "PURGE TRANSMISSION" in

the Operation section of this manual.

TO ADJUST STEERING WHEEL

ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble with crossbars horizontal. Tighten securely.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not

adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or

camber, contact a Sears or other qualified service center.

TO REMOVE WHEEL FOR REPAIRS

1.Block up axle securely.

2.Remove axle cover, retaining ring and washers to allow wheel removal (rear wheels have a square key - Do not lose).

3.Repair tire and reassemble.

NOTE: On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

4.Replace washers and snap retaining ring securely in axle groove.

5.Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, purchase and use tire sealant from Sears. Tire sealant also prevents tire dry rot and corrosion.

Retaining, "

CoverAxte __

Square Key ....._ '

(Rear Wheel Only)

25

Image 25
Contents Jcriiftsmrnj Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation II. Slope OperationDo not IV. ServiceIII. Children Across Sears Installation Service Product SpecificationsCustomer Responsibilities Repair Protection AgreementsSlope Sheet Steering WheelTools Required for Assembly Howto SET UP Your TractorCheck Battery To Remove Tractor fromAssemble Gauge Wheels to Mower Deck Install SeatCheck Deck Levelness Install Mulcher PlateCheck for Proper Position of ALL Belts Check Brake SystemAutomatic Models only Attachment Clutch Lever Used Know Your TractorLift Lever Plunger Used to release To Adjust Mower Cutting Height HOW to USE Your TractorTo SET Parking Brake To Move Forward and BackwardTo Operate Mower To Adjust Gauge WheelsTo Operate On Hills Do not drive up or downTo Start Engine Before Starting the EngineTransmission Engaged Transmission Disengaged MentsPurge Transmission Automatic Transmission Warm UPMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Check tire pressureTractor BatteryBlade Removal To Sharpen BladeTransaxle Pump Fluid EngineLubrication Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning AIR FilterTractor To Install MowerTo Remove Mower Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Adjust Brake To Check and Adjust BrakeTo Replace Motion Drive Belt Transmission Removal Replacement Transaxle Motion Control Lever Neutral AdjustmentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsTo Attach Jumper Cables Replacing BatteryTo Remove CABLES, Reverse Order To Replace Headlight Bulb To Adjustthrottle Control CableEngine Acceleration Test Fuel System BatteryEngine OIL CylindersIgnition switch Troubleshooting ChartCause Correction Problem Cause Problem Cause Correction AMETdLUTCH Tractor - Model Number SchematicElectrical Tractor - Model NumberKEY Part Description Tractor - Model Number ElectricalTractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number Ground Drive 25/32 Tractor - Model Number 917.273840 Steering Assembly Tractor - Model Number 917.273840 Steeringassembly Control Throttle/Choke Tractor - Model Number EngineKEY Part Tractor - Model Number Seat AssemblyDescription Tractor - Model Number DecalsLink Front Tractor - Model Number Lift AssemblyTractor - Model Number Mower Deck 177563 Bracket, Deflector 124 351 64 \ 125 107 900 Ill 625 Cylinder HEAD, Valve and Breather Crankcase Headnalvbreathercrankcase Iiiiiiiiiiiiiiiiiii Not Illustrated Starting System OIL PAN/LUBRICATION OIL PAN/LUBRICATION KEY Part NO. no Iliiii 77% Crankshaft Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.27384 specifications

The Craftsman 917.27384 is a powerful lawn tractor designed to deliver both efficiency and versatility for homeowners who strive for a pristine lawn. Known for its robust construction and functional design, this model is particularly favored for its ability to tackle various lawn care tasks with ease, making it an essential tool for anyone maintaining a sizeable outdoor area.

One of the standout features of the Craftsman 917.27384 is its strong engine performance. It is typically powered by a reliable and efficient 19.5 HP Briggs & Stratton engine, designed to provide ample power to handle tough mowing conditions. This reliable engine ensures smooth operation and longevity, helping users complete their mowing tasks without interruptions for maintenance or repairs.

Another notable characteristic is its cutting deck. The Craftsman 917.27384 comes equipped with a 42-inch cutting deck, which allows for efficient mowing by covering a wide area with each pass. The deck is designed with multiple height adjustment options, providing flexibility to adapt to various grass types and desired cutting lengths. This feature not only enhances the overall appearance of your lawn but also promotes healthy grass growth.

Additionally, this lawn tractor boasts several user-friendly technologies that enhance the mowing experience. The model features a foot-controlled hydrostatic transmission, allowing for smooth acceleration and deceleration without the need for shifting gears. This is particularly beneficial for navigating around obstacles and adjusting speed quickly as needed.

Comfort is another important aspect of the Craftsman 917.27384. It is designed with an ergonomic seat and easy-to-reach controls, ensuring that operators can mow comfortably for extended periods. The 917.27384 also includes a large fuel tank that minimizes refueling frequency, ensuring that users can complete larger jobs without interruption.

In terms of maintenance, the Craftsman lawn tractor is user-friendly, featuring easily accessible components for routine checks and servicing. This attention to detail makes it simple for homeowners to keep the tractor in optimal condition over the years.

Overall, the Craftsman 917.27384 combines power, ease of use, and comfort, making it an excellent choice for homeowners seeking a reliable lawn tractor capable of delivering impressive results. Whether you are mowing, bagging, or mulching, this model is designed to meet diverse lawn care needs effectively.