Craftsman 917.27384 owner manual Install Seat, Assemble Gauge Wheels to Mower Deck

Page 9

INSTALL SEAT

Adjust seat before tightening adjustment knob.

1.Remove adjustment knob and flat washer securing seat to cardboard

packing and set aside for assembly of seat to tractor.

2.Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

3.Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

4.Push down on seat to engage shoulder

bolt in slot and pull seat towards rear of tractor.

5.Pivot seat and pan forward and as- semble adjustment knob and flat

washer loosely. Do not tighten.

6.Lower seat into operating position and sit in seat.

7.Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

8.Get off seat without moving its ad- justed position.

9.Raise seat and tighten adjustment knob securely.

Seat

Seat Pan

Bolt

2.Release parking brake by depressing clutch/brake pedal.

3.Place freewheel control in '"trans- mission disengaged" position (See "TO TRANSPORT" in the Operation section of this manual).

4.Roll tractor forward off skid.

5.Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See

Operation section for location and function of controls)

_i, WARNING: Before starting, read, un- derstand and follow all instructions in the

Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure

the area in front of tractor is clear of other people and objects.

1.Be sure all the above assembly steps have been completed.

2.Check engine oil level and fill fuel tank with gasoline.

3.Place freewheel control in "trans- mission engaged" position. (See "TO TRANSPORT" in the Operation section of this manual).

4.Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

5.Place motion control lever in neutral

(N)position.

6.Press lift lever plunger and raise

attachment lift lever to its highest posi- tion.

7.Start the engine. After engine has started, move throttle control to idle position.

8.Release parking brake.

9.Slowly move the motion control lever forward and slowly drive tractor off skid.

10.Apply brake to stop tractor, set parking brake and place motion control lever in

neutral position.

11.Turn ignition key to "STOP" position. Continue with the instructions that follow.

NOTE: You may now roll or drive your

tractor off the skid. Follow the appropriate instruction below to remove the tractor

from the skid.

TO ROLL TRACTOR OFF SKID (See

Operation section for location and function of controls)

1. Press lift lever plunger and raise

ASSEMBLE GAUGE WHEELS TO MOWER DECK

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are prop- erly adjusted to ensure optimum mower performance.

1. Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. As-

attachment lift lever to its highest po-

sition.

9

semble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16

center Iocknuts and tighten securely.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Jcriiftsmrnj Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation II. Slope OperationIV. Service Do notIII. Children Across Sears Installation Service Product SpecificationsCustomer Responsibilities Repair Protection AgreementsSlope Sheet Steering WheelTools Required for Assembly Howto SET UP Your TractorCheck Battery To Remove Tractor fromAssemble Gauge Wheels to Mower Deck Install SeatCheck Deck Levelness Install Mulcher PlateCheck for Proper Position of ALL Belts Check Brake SystemAutomatic Models only Know Your Tractor Attachment Clutch Lever UsedLift Lever Plunger Used to release To Adjust Mower Cutting Height HOW to USE Your TractorTo SET Parking Brake To Move Forward and BackwardTo Operate Mower To Adjust Gauge WheelsTo Operate On Hills Do not drive up or downTo Start Engine Before Starting the EngineTransmission Engaged Transmission Disengaged MentsPurge Transmission Automatic Transmission Warm UPMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Check tire pressureTractor BatteryBlade Removal To Sharpen BladeEngine Transaxle Pump FluidLubrication Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning AIR FilterTo Install Mower TractorTo Remove Mower Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt Belt RemovalTo Check and Adjust Brake To Adjust BrakeTo Replace Motion Drive Belt Transmission Removal Replacement Transaxle Motion Control Lever Neutral AdjustmentFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery To Attach Jumper CablesTo Remove CABLES, Reverse Order To Adjustthrottle Control Cable To Replace Headlight BulbEngine Acceleration Test Fuel System BatteryEngine OIL CylindersTroubleshooting Chart Ignition switchCause Correction Problem Cause Problem Cause Correction AMETdLUTCH Tractor - Model Number SchematicElectrical Tractor - Model NumberKEY Part Description Tractor - Model Number ElectricalTractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number 917.273840 Chassis and Enclosures Tractor - Model Number Ground Drive 25/32 Tractor - Model Number 917.273840 Steering Assembly Tractor - Model Number 917.273840 Steeringassembly Control Throttle/Choke Tractor - Model Number EngineKEY Part Tractor - Model Number Seat AssemblyDescription Tractor - Model Number DecalsLink Front Tractor - Model Number Lift AssemblyTractor - Model Number Mower Deck 177563 Bracket, Deflector 124 351 64 \ 125 107 900 Ill 625 Cylinder HEAD, Valve and Breather Crankcase Headnalvbreathercrankcase Iiiiiiiiiiiiiiiiiii Not Illustrated Starting System OIL PAN/LUBRICATION OIL PAN/LUBRICATION KEY Part NO. no Iliiii 77% Crankshaft Page Suggested Guide for Sighting Slopes for Safe Operation Get it fixed, at your home or ours

917.27384 specifications

The Craftsman 917.27384 is a powerful lawn tractor designed to deliver both efficiency and versatility for homeowners who strive for a pristine lawn. Known for its robust construction and functional design, this model is particularly favored for its ability to tackle various lawn care tasks with ease, making it an essential tool for anyone maintaining a sizeable outdoor area.

One of the standout features of the Craftsman 917.27384 is its strong engine performance. It is typically powered by a reliable and efficient 19.5 HP Briggs & Stratton engine, designed to provide ample power to handle tough mowing conditions. This reliable engine ensures smooth operation and longevity, helping users complete their mowing tasks without interruptions for maintenance or repairs.

Another notable characteristic is its cutting deck. The Craftsman 917.27384 comes equipped with a 42-inch cutting deck, which allows for efficient mowing by covering a wide area with each pass. The deck is designed with multiple height adjustment options, providing flexibility to adapt to various grass types and desired cutting lengths. This feature not only enhances the overall appearance of your lawn but also promotes healthy grass growth.

Additionally, this lawn tractor boasts several user-friendly technologies that enhance the mowing experience. The model features a foot-controlled hydrostatic transmission, allowing for smooth acceleration and deceleration without the need for shifting gears. This is particularly beneficial for navigating around obstacles and adjusting speed quickly as needed.

Comfort is another important aspect of the Craftsman 917.27384. It is designed with an ergonomic seat and easy-to-reach controls, ensuring that operators can mow comfortably for extended periods. The 917.27384 also includes a large fuel tank that minimizes refueling frequency, ensuring that users can complete larger jobs without interruption.

In terms of maintenance, the Craftsman lawn tractor is user-friendly, featuring easily accessible components for routine checks and servicing. This attention to detail makes it simple for homeowners to keep the tractor in optimal condition over the years.

Overall, the Craftsman 917.27384 combines power, ease of use, and comfort, making it an excellent choice for homeowners seeking a reliable lawn tractor capable of delivering impressive results. Whether you are mowing, bagging, or mulching, this model is designed to meet diverse lawn care needs effectively.
Top Page Image Contents