Craftsman 917.289280 manual To USE Cruise Control, System Characteristics, To Adjust Gauge Wheels

Page 12

TO USE CRUISE CONTROL

The cruise control feature can be used for

forward travel only.

SYSTEM CHARACTERISTICS

The cruise control should only be used while mowing or transporting on relatively smooth, straight surfaces. Other conditions such as trimming at slow speeds may cause the cruise control to disengage. Do not use the cruise control on slopes, rough terrian or while trimmimg or turning.

•With forward drive pedal (K) depressed to desired speed, pull cruise control lever (J) up and hold while lifting your foot off the pedal, then release the lever.

To disengage the cruise control, depress the brake pedal or tap on forward drive pedal.

TO ADJUST MOWER CUTTING HEIGHT The position of the attachment lift lever (A) determines the cutting height.

TO ADJUST GAUGE WHEELS

Gauge wheels are properly adjusted

when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions, NOTE: Adjust gauge wheels with tractor on a flat level surface.

I, Adjust mower to desired cutting height (See "TO ADJUST MOWER CUTTING HEIGHT" in this section of manual).

2.With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appro- priate hole. Tighten securely.

3.Repeat for all, installing gauge wheel in same adjustment hole.

9}16

-Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil condi- tions, height of grass and types of grass being mowed.

•The average lawn should be cut to ap- proximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate

growth.

,For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitating or cutting off when operating your equip- ment on rough, rolling terrain or hills.

1.Select desired height of cut with at- tachment lift lever.

2.Start mower blades by engaging at- tachment clutch control.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Lawn Tractor Craftsman Limited Warranty TWO Years on Tractor Days on BatteryGeneral Operation II, Slope Operation I11. ChildrenIV. Towing Safe Handling of GasolineGeneral Service Product 030Some limitations and exclusions apply Keys Check Tire Pressure Check Deck LevelnessCheck for Proper Position ALL Belts Check Brake System IXU Know Your Tractor THROTTLE/CHOKE ControlAttachment Clutch Lever To Move System Characteristics To Adjust Gauge WheelsTo USE Cruise Control To Operate MowerUsing the Reverse Operation System To Operate on HillsTo Transport Towing Carts and Other ATTACH- Ments Before Starting the Engine Check Engine OIL LevelADD Gasoline To Start EngineAutomatic Transmission Warm UP RGE TransmissionMowing Tips Maintenance ScheduleGeneral Recommendations IFront WheelBattery TractorBrake Operation TiresTransaxle Cooling Transaxle Pump FluidBelts Engine LubricationMuffler Egadora est6 a tces las ruedas Egadora sin, -ompletoen las a protecci6nTo Remove MowerAttach Mower Side Suspension ArmsComo USA MientoVisual SIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentPrecision SIDE-TO-SIDE Adjustment To Level MowerBelt Installation To Replace Mower Blade Drive BeltBelt Removal To Replace Motion Drive BeltEmpesar EL ,R LA Trans To Check BrakeFront Wheel TOE-IN/CAMBER To Remove Wheel for RepairsReplacing Battery Close hoodDN Para LA Especia- aci6nProblem Cause Correction Engine will notProblem Cause CorrectionEngine clicks but GeneralesPeligro Poor cut uneven cuttingDvertei Headlights not workingWhen turning engine OFF ContraportadaWill not Charge Ill Ffl I11 Ili ITI Rtl TI ==1Problem Loss of dri Engine ba when turnitSee appro GARANTiA Limitada DE CraftsmanVice center Other enterEngine con run when e IV. RemolqueLoss of po EngagedVice center Battery AdtightWire nnector Hoja de pendiente Llaves Tubo de desagQePara Hacer Rodar EL Tractor Revision DE LA Presion DE LAS LlantasRevision DE LA Posicion Adecuada DE Todas LAS Correas To CheckStall MOW LucesUncut gr With alltirParada Cuchillas DE LA Segadora Impulsion DE RecorridoUtilizar EL Mando Crucero Caracteristicas TicnicasPara Ajustar LA Altura DE Corte DE LA Segadora Paraajustar LasruedascalibradorasTransmlsi6n Desenganchada Antes DE Hacer Arrancar EL Motor Agregue GasolinaPRECAUOI6N Para Hacer Arrancar EL MotorOo27J On ROSPurgar LA Transmision Consejos Para SegarMantenimiento OnAsSCl Recomendaciones GeneralesCuidado DE LA Cuchilla BATERiAEnfriamiento DEL Transeje Nivel DEL Fluido DE LA Bomba DEL TransejeCorreas Motor LUBRICACI6NFiltro DEL Aire Filtro DE Aceite DEL MotorBUJiAS LimpiezaPara DESiVIONTAR LA Cortadora DE Cisped Instale LA SegadoraTin conditions Fije LA P1EZA DE Union Anterior ETloje la tuerca Para Nivelar LA SegadoraAjuste DE Delante a Atras Stopping Mower BLAtions Impresion / Inclinacion DE LAS RUE DAS Delanteras Para Remover LAS Ruedas Para Hacer ReparacionesPara Adjuntar LOS Cables DE Empalme Page BATERiA Identificacion DE Problemas Agreement 00 profeErvice ation of home UnexpectedIDENTIFICAC1ON DE Problemas Problema CausaSe pen Dirigido a un centre de servicio SearsIDENTIFICAClON DE Problemas Las cuchillasTraction Est&n funcionando Si equipadasGenera Back Cover Your Home 8o0469463 Aan.CanadaVisit our Cra
Top Page Image Contents