Craftsman 917.289280 Tractor, Brake Operation, Tires, Check Operator Presence System, Blade Care

Page 18

TRACTOR

Always observe safety rules wllen per- forming any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments

section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as de- scribed, repair the problem immediately.

°The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE SYSTEM

o When the engine is running, any at- tempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any at- tempt by the operator to leave the seat should shut off the engine.

°The attachment clutch should never op- erate unless the operator is in the seat.

ROS "ON" Position Engine "ON" Position (Normal Operating)

CHECK REVERSE OPERATION (ROS) SYSTEM

°When the engine is running with the ignition switch in the engine "ON" posi- tion and the attachment clutch engaged, any attempt by the operator to drive in

reverse should shut off the engine.

,When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in

reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be

sharp, Replace worn, bent or damaged blades.

CAUTION; Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL

!.Raise mower to highest position to al- low access to blades.

NOTE; Protect your hands with gloves and/or wrap blade with heavy cloth.

2.Remove blade bolt by turning counter- clockwise.

3.install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bott is heat treated.

Blade

Blade Belt

Assembly

Center Hole

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. How-

ever, periodic charging of the battery with an automotive charger will extend its life.

°Keep battery and terminals clean. o Keep battery bolts tight.

, Keep small vent holes open.

, Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

•LOS accesol

periodo del que la tran_ AVISO: Si se

3000 pies) o, [0°C]), la mezI debe ser aju,, del motor. (V_ RADOR" en I_

este manual). PURGAR Li

_PRECAUC

ganche la pal_ cuando el tool

Para asegurar uada, es reoot purgada ante_

era vez. Estet adentro de ta

durante el trar IMPORTANTt_ debe ser remc debe ser purg antes de open

1.Para may( en una sul cualquier € apagado y

2.Desengan control de

desengant PORTE'Ie

3.Sentado e ei motor. E

motor, muc

a la posici, mano.

_PRECAUC

puede que de las ruedas.

4, Apretar e] el rondo, n

sottar el pc atr&s hast_

(5)segunc procedimi_

5.Apague el estacionar

6.Enganche control de

conducir (_ esta seccit

7.Sentado e el motor. E

motor, mu_ media (1/2 maria

8.Conduzca

aproximad hacia marl

Repita eat,

Su transmisi6! para la operac

t8

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Lawn Tractor Craftsman Limited Warranty TWO Years on Tractor Days on BatteryGeneral Operation IV. Towing II, Slope OperationI11. Children Safe Handling of GasolineGeneral Service Product 030Some limitations and exclusions apply Keys Check for Proper Position ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemIXU Know Your Tractor THROTTLE/CHOKE ControlAttachment Clutch Lever To Move To USE Cruise Control System CharacteristicsTo Adjust Gauge Wheels To Operate MowerUsing the Reverse Operation System To Operate on HillsTo Transport ADD Gasoline Towing Carts and Other ATTACH- MentsBefore Starting the Engine Check Engine OIL Level To Start EngineAutomatic Transmission Warm UP RGE TransmissionMowing Tips General Recommendations MaintenanceSchedule IFront WheelBrake Operation BatteryTractor TiresBelts Transaxle CoolingTransaxle Pump Fluid Engine LubricationMuffler To Remove Egadora est6 a tces las ruedasEgadora sin, -ompletoen las a protecci6n MowerComo USA Attach Mower Side SuspensionArms MientoPrecision SIDE-TO-SIDE Adjustment Visual SIDE-TO-SIDE AdjustmentFRONT-TO-BACK Adjustment To Level MowerBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER Empesar EL ,R LA TransTo Check Brake To Remove Wheel for RepairsReplacing Battery Close hoodDN Para LA Especia- aci6nProblem Cause Correction Engine will notEngine clicks but ProblemCause Correction GeneralesDvertei PeligroPoor cut uneven cutting Headlights not workingWhen turning engine OFF ContraportadaWill not Charge Ill Ffl I11 Ili ITI Rtl TI ==1See appro ProblemLoss of dri Engine ba when turnit GARANTiA Limitada DE CraftsmanVice center Other enterLoss of po Engine con run when eIV. Remolque EngagedVice center Battery AdtightWire nnector Hoja de pendiente Llaves Tubo de desagQeRevision DE LA Posicion Adecuada DE Todas LAS Correas Para Hacer Rodar EL TractorRevision DE LA Presion DE LAS Llantas To CheckStall MOW LucesUncut gr With alltirParada Cuchillas DE LA Segadora Impulsion DE RecorridoPara Ajustar LA Altura DE Corte DE LA Segadora Utilizar EL Mando CruceroCaracteristicas Ticnicas Paraajustar LasruedascalibradorasTransmlsi6n Desenganchada PRECAUOI6N Antes DE Hacer Arrancar EL MotorAgregue Gasolina Para Hacer Arrancar EL MotorPurgar LA Transmision Oo27JOn ROS Consejos Para SegarSCl MantenimientoOnAs Recomendaciones GeneralesCuidado DE LA Cuchilla BATERiACorreas Enfriamiento DEL TransejeNivel DEL Fluido DE LA Bomba DEL Transeje Motor LUBRICACI6NBUJiAS Filtro DEL AireFiltro DE Aceite DEL Motor LimpiezaPara DESiVIONTAR LA Cortadora DE Cisped Instale LA SegadoraTin conditions Fije LA P1EZA DE Union Anterior EAjuste DE Delante a Atras Tloje la tuercaPara Nivelar LA Segadora Stopping Mower BLAtions Impresion / Inclinacion DE LAS RUE DAS Delanteras Para Remover LAS Ruedas Para Hacer ReparacionesPara Adjuntar LOS Cables DE Empalme Page BATERiA Ervice ation of home Identificacion DE ProblemasAgreement 00 profe UnexpectedSe pen IDENTIFICAC1ON DE ProblemasProblema Causa Dirigido a un centre de servicio SearsTraction IDENTIFICAClON DE ProblemasLas cuchillas Est&n funcionando Si equipadasGenera Back Cover Your Home 8o0469463 Aan.CanadaVisit our Cra

28928, 917.289280 specifications

The Craftsman 917.289280 and 917.28928 are riding lawn mowers designed for homeowners looking for a reliable and effective solution for lawn care. These models are particularly notable for their blend of power, ease of use, and advanced features that enhance the mowing experience.

One of the standout characteristics of the Craftsman 917.289280 and 917.28928 is their robust engine. Equipped with a powerful 19 horsepower engine, these mowers ensure a strong performance, allowing users to tackle various terrains and thick grasses with ease. The engine is complemented by an efficient automatic transmission that provides smooth acceleration and deceleration, making it easy to navigate around the yard or garden.

The cutting deck is another important feature of these models. With a wide 42-inch cutting width, the mowers can cover more ground in fewer passes, significantly reducing mowing time. The cutting height adjustment is another convenient feature, allowing users to customize the height to suit their lawn’s needs, whether it's a clean trim or a higher cut during the growing season.

Technology plays a key role in the design of the Craftsman 917.289280 and 917.28928. The mowers are equipped with an added ergonomic dashboard that includes an easy-to-read fuel gauge and key start ignition. This design provides intuitive control and enhances the overall user experience. The mowers also incorporate safety features such as an automatic shut-off system when the operator leaves the seat, ensuring safe operation at all times.

Durability is a fundamental characteristic of these models. Built with a sturdy steel frame and high-quality materials, the Craftsman mowers are designed to withstand the rigors of regular use. The rear-wheel drive system enhances traction and maneuverability, allowing users to navigate tricky areas, including slopes and uneven ground.

Additionally, the mowers’ compact design allows for easy storage and transport. Their tight turning radius makes them adept at maneuvering around landscaping and obstacles, further increasing their efficiency and reducing the need for trimming.

In summary, the Craftsman 917.289280 and 917.28928 riding lawn mowers deliver a powerful performance with their reliable engines, versatile cutting capabilities, and user-friendly features. These models are ideal for homeowners seeking a practical and effective solution for lawn maintenance, combining modern technology with robust construction for lasting value.
Top Page Image Contents