Craftsman 917.289240 Tractor, Brake Operation, Tires, Check Operator Presence System

Page 17

TRACTOR

Always observe safety rules when performing any maintenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments

section of this manual).

TIRES

Maintain proper air pressure in all tires (See the sides of tires for proper PSI).

Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber.

Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause

tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

The engine should not start unless the

brake pedal is fully depressed, and the attachment clutch control is in the disen-

gaged position.

CHECK OPERATOR PRESENCE SYSTEM

When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

When the engine is running and the at- tachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

The attachment clutch should never oper- ate unless the operator is in the seat.

CHECK REVERSE OPERATION (ROS) SYSTEM

When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to drive in reverse should shut off the engine.

When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to drive in reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

_, CAUTION: Use only a replacement

blade approved by the manufacturer of your tractor. Using a blade not approved by the

manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL

1.Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/ or wrap blade with heavy cloth.

2.Remove blade bolt by turning counter- clockwise.

3.Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

4.Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

iMPORTANT: Special blade bolt is heat treated.

 

Star

Center Hole

\

Blade Bolt

Mandrel

(Special) "----._ _

Assembly

Blade

 

ROS "ON" Position Engine "ON" Position (Normal Operating)

17

Image 17
Contents SEARS, Roebuckand CO., Hoffman ESTATES, IL 60179 U.S.A LAW TractoTWO Years on RiDiNG Equipment Craftsman Full WarrantyGeneral Operation Safe Handling of Gasoline ServiceGeneral Service Repair Protection Product SpecificationsTo Adjust Seat Tools Required for AssemblyCheck Battery To Remove Tractor from CartonCheck Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake System@@@ Know Your Tractor Stopping HOW to USE Your TractorTo SET Parking Brake To Adjust Gauge Wheels To Adjust Mower Cutting HeightTo Move Forward Backward To Operate MowerReverse Operation System ROS To TransportTransmission Engaged Transmission Disengaged To Start Engine Before Starting the EngineAutomatic Transmission Warm UP Check Engine OIL LevelNever engage or disengage Purge TransmissionGeneral Purpose Grease @Refer to Maintenance Engine Section Lubrication ChartGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence System and Reverse Operation System ROSEngine Transaxle Pump FluidEngine Cooling System AIR FilterSpark Plugs MufflerDeck Washout Port CleaningTo Remove Mower To Install Mower03042tex FRONT-TO-BACK Adjustment Visual SIDE-TO-SIDE AdjustmentPrecision SIDE-TO-SIDE Adjustment To Level MowerTo Replace Mower Blade Drive Belt Belt InstallationBelt Removal To Replace Motion Drive BeltTo Start Engine with Weak Battery Transaxle Motion Control Lever Neutral AdjustmentTo Remove Wheel for Repairs To Attach Jumper CablesInterlocks and Relays To Remove Hood & Grill AssemblyReplacing Battery Cylinders Fuel SystemEngine OIL Correction Problem CauseWill not start Loss of power ProblemcauseDischarge Headlights not working If so equipped CuttingProblem Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationDOS Aiios Para EL Equipo Tractor Sears, Roebuck and Co., Hoffman Estates, ILFuncionamiento General Lesiones graves o la muerteIV. Remolque III. NiiosManipulacion Segura DE LA Gasolina Operaciones DE Servicio GeneralesPage Producto Especificaciones DELResponsabilidades DEL Cliente Servicio DE Instalacion SearsPara Remover EL Tractor DE Herramientas Necesarias Para EL MontajeLA Caja DE Carton Desempaque LA Caja DE Carton Verifique LA BateriaRevjsion DE LA Nivelacion DEL Conjunto Revision DE LA Presion DE LAS LlantasRevision DEL Sistema DE Frenos Jlista DE Revision@@@ Istema DE Funcionamiento Hacia Familiaricese CON SU TractorSU Tractor Parada Como Usar SU TractorMiento LA Segadora Para Operar EN Cerros Usar EL Sistema DE Funcionamiento ATR,SPara Transportar Transmision Enganchada Transmision DesenganchadaAgreguegasolina Consejos Para Segar Purgar LA TransmisionAntes DE Cada USO Tabla DE LubricacionRecomendaciones Generales VI= Rifiez Sistema Func Ionam Iento AT R/,S ROS TractorLlantas Transeje MotorCorreas Para Cambiar EL Aceite DEL MotorLimpieza BUJiASManguera Puerto de Lavado Adaptador de Boq Instale LA Segadora DE CespedPara Desmontar LA Cortadora 03042tex Regulacion Visual DE Lado a Lado Para Nivelar LA SegadoraRegulacion DE LA Precision DE Lado Ajuste DE Delante a ATR,SRemocion DE LA Correa Paracambiarla Correa DE Impulsion DE LA Cuchilla SegadoraInstalacion DE LA Correa Montaje DE LA CorreaPara ADJ Untar LOS CAB LES D E EM Palm E MEC.&NICOPara Cambiar EL Fusible Reemplazar LA BateriaPara Remover EL Conjunto DEL Capo Y DEL Enrejado Para Cambiar LA Bombilla DE LA LUZ DelanteraSistema DE Combustible OtrosAceite DEL Motor CilindrosEstrangulacion Choke Problema Causa CorreccionIDENTIFICACI6N DE Problemas Correccion Identificacion DE ProblemasProblemacausa Las cuchillas Page 15GRADOS MAX Operacion SeguraYour Home Needmore