Craftsman 917.37192 manual HOW to USE Your Lawn Mower

Page 8

The operationof any lawn mower can result

in foreign objects thrown into the eyes,which can result in severe eye dam-

age, Always wear safety glasses or eye shieldswhile operating your lawn mower or performing any adjustmentsor repairs, We recommend a standardsafety glasses or wide vision safety maskworn over spectacles,

HOW TO USE YOUR LAWN MOWER

ENGINE SPEED

The engine speed was set at the factory

for optimum performance, Speed is not adjustable,

ENGINE ZONE CONTROL

_I, CAUTION: Federal regulations require

an engine control to be installed on this lawn mower in order to minimize the

risk of blade contact injury. Do not under

any circumstances attempt to defeat the function of the operator control. The blade turns when the engine is running.

•Your lawn mower is equipped with an operator presence control bar which

requires the operator to be positioned behind the lawn mower handle to start

and operate the lawn mower.

DRIVE CONTROL

•Self-propelling is controlled by hold- ing the operator presence control bar down to the handle and pulling the drive control bar up to the handle. The closer

to the handle the bar is pulled, the faster the unit will travel.

•Forward motion will stop when either the operator presence control bar or drive control bar are released, To stop forward motion without stopping engine, release the drive control bar only, Hold operator presence control bar down against handle to continue mowing

without self-propelling,

NOTE: If after releasing the drive control the mower will not roll backwards, push the mower forward slightly to disengage drive wheels,

•To keep drive control engaged when turning corners, push down on the handle to lift the front wheels off the ground while turning lawn mower,

O )resence control bar

DRIVEDrive

CONTROLcontrol bar

ENGAGED

DRIVE

CONTROL

DISENGAGED

TO ADJUST,

MOVE DOWN

TO NEXT HOLE

DRIVE CONTROL ADJUSTMENT

Over time, the drive control system may become "loose", resulting in decreased speed. There are holes in the drive control housing to increase tension on the drive cable. Proceed as follows:

1.Turn unit off and disconnect spark plug wire from spark plug.

2.Loosen nut, move drive control hous- ing down handle to the next hole and retighten nut.

3.Operate mower to test drive speed.

4.If condition fails to improve after the above steps (forward speed remains the same), your drive belt is worn and should be replaced.

TO ADJUST CUTTING HEIGHT

Raise wheels for low cut and lower wheels for high cut, adjust cutting height to suit

your requirements. Medium position is best for most lawns.

•To change cutting height, squeeze ad- juster lever toward wheel. Move wheel

up or down to suit your requirements. Be sure all wheels are in the same setting.

NOTE: Adjuster is properly positioned when plate tab inserts into hole in lever. Also, 9-position adjusters (if so equipped) allow lever to be positioned between the plate tabs.

LEVER BACKWARD

Plate tab

TO LOWER MOWER

 

LEVER FORWARD TO RAISE MOWER Lever

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Craftsman Year Full Warranty on Craftsman Lawn Mower Do not IV. Safe Handling of GasolineAPI SG-SL SAE RJ19HXRepair Protection Agreements HOW to SET UP Your Mower Meets Cpsc Safety Requirements Know Your Lawn MowerHOW to USE Your Lawn Mower Rear Bagging Side DischargingFor Rear Bagging For Side DischargingBefore Starting Engine To Empty Grass CatcherADD OIL ADD GasolineTo Start Engine MowingTips Mulching Mowing TipsLubrication General RecommendationsBefore Each USE Lawn Mower Gear CaseTo Clean AIR Filter EngineTo Change Engine OIL AIR FilterCleaning Clean Under Drive CoverWater Washout Feature MufflerTo Adjust Handle Rear DeflectorTo Remove Drive Belt To Replace Drive BeltSqueeze To Fold HandleCarburetor Problem Cause OtherCylinder OFFProblem CauseGarantia Reglas de Seguridad No Hacer OperacionHacer SERVlClO Rendimiento DE LA Segadora Cesped Familiaricese CON SU Segadora Cumple CON LOS Requisitos DE Seguridad DE LA CpscAjuste DEL Mando Como Usar SU Segadora Velocidad DEL MotorControl DE LA Impulsion Para Convertir LA Segadora Segadoras CON Descarga TraseraSegadoras CON Descarga Lateral Para Descarga LateralAgregue Gasolina Antes DE Hacer Arrancar EL Motor Agregue AceiteImportante Para Hacer Arrancar EL Motor Consejos Para Segar Y ACOL- CharAntes DE Cada USO LubricacionTabla DE LubricacionSegadora LlantasRuedas DE Impulsion Cuidado DE LA CuchillaFiltro DE Aire Recogedor DE C#SPEDCaja DE Engranajes Derrubio DEL Agua LimpiezaLimpie Debajo DE LA Cubierta DE LA Impulsion Para Ajustar LA Altura DE Corte Desviador TraseroPara Remover Correa DE Impulsion Para Ajustar EL MangoMotor Velocidad DEL Motor Hacia AdelanteProblema Motor Sistema DE CombustibleCausa Llena si vieneCraftsman Rotary Lawn Mower - Model Number Craftsman Rotary Lawn Mower - Model Number KEYPart Part Description\ \ 67725 Washer Flat 183509 701037 Selector Briggs & Stratton 4=CYCLE Engine Model Number 126L02-1082-FI Repair ManuaiCarburetor Overhaul KIT CarburetorGasket SET Operators Manual Emissions Label209 Engine Gasket SETBriggs & Stratton 4=CYCLE Engine KEY Part584 697734 Cover-Breather Need More HELP?
Top Page Image Contents