Craftsman 917.27377 manual Howto SET UP Your Tractor, Tools Required for Assembly

Page 8

Your new tractor has been assembled at the factory with the exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness. Review the video cassette before you begin.

TOOLS REQUIRED FOR

ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes you need

are

listed

below.

 

 

(1)

3/4"wrench

(1)

Pliers

(2)

7/16"

wrench

(1)

Utility knife

(1)

Tire

pressure

gauge

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM

CARTON

UNPACK CARTON

1.Remove all accessible loose parts and parts boxes from carton.

2.Cut along dotted lines on all four pan- els of carton. Remove end panels and lay side panels flat.

3.Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL

ASSEMBLE EXTENSION SHAFT AND BOOT

1.Slide extension shaft onto lower steer-

ing shaft. Align mounting holes in ex- tension and lower shafts and install 1/4

hex bolt and Iocknut. Tighten securely. IMPORTANT: Tighten bolt and nut se- curely to 10-12 ft. Ibs torque.

2.Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

3.Position front wheels of the tractor so they are pointing straight forward.

4.Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

5.Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

6.Assemble large flat washer, 1/2 hex nut and tighten securely.

7.Snap steering wheel insert into center of steering wheel.

_

_1/2

Hex Nut

 

Insert

Large Flat Washer

8.Remove protective materials from trac- tor hood and grill.

IMPORTANT: Check for and remove any

staples in skid that may puncture tires where tractor is to roll off skid.

HOWTO SET UP YOUR TRACTOR

CHECK BATTERY

1. Lift hood to raised position.

NOTE: If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See "BATTERY" in Maintenance section of this manual for charging instruc- tions).

_'.. .-- ,' Label

i-

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Icrrftsmrni Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation IV. Service Do notPage Product Specifications Sears Installation ServiceCustomer Responsibilities Repair Protection AgreementsKeys Slope Sheet Steering WheelSeat Howto SET UP Your Tractor Tools Required for AssemblyTo Remove Tractor from Before Removing Tractor from Skid Attach Steering WheelInstall Seat To Rolltractor OFF Skid SeeInstall Mulcher Plate If previously removedCheck Deck Levelness Check for Proper Position of ALL Belts@@@@@ Know Your Tractor Attachment Clutch Lever UsedTo Move Forward and Backward HOW to USE Your TractorTo SET Parking Brake To Adjust Gauge Wheels To Stop Mower BladesTo Operate On HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start EngineMowing Tips Mulching Mowing TipsChart General RecommendationsBefore Each USE LubricationTo Sharpen Blade TractorBlade Removal Battery To Clean Battery and TerminalsEngine Transaxle CoolingClean AIR Screen Clean AIR INTAKE/COOLING AreasAIR Filter IN-LINE Fuel FilterCleaning To Install MowerTractor To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentBelt Installation To Check and Adjust BrakeTo Adjust Brake To Check BrakeTransaxle Gear Shift Lever NEU- Tral Adjustment Front Wheel TOE-IN/CAMBERReplacing Battery To Start Engine with a Weak BAT- TE RYTo Attach Jumper Cables Interlocks and RelaysTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control Battery Remove mower from tractor for winterFuel System Engine OILCause Correction Troubleshooting ChartIgnition switch Problem Cause Problem Cause Correction Tractor - Model Number Schematic RED01115BLACKTractor - Model Number Electrical KEY Part Description Tractor -- Model Number 917.273770 Chassis and Enclosures 175710 Pivot Bracket Tractor -- Model Number Ground Drive X .1845/1865 Tractor -- Model Number Steering Steering Tractor -- Model Number Engine 137180 Tractor -- Model Number Seat Assembly KEY PartTractor -- Model Number Decals 186388Tractor -- Model Number Lift Assembly Tractor -- Model Number Lift Assembly 1o6 1o2 1o3los Tractor -- Model Number Mower DeckOnly 35A Teeth 523 51B 20@ 220 798 697890 Screw Suggested Guide for Sighting Slopes for Safe Operation 6E/A R,. o 4,0

917.27377 specifications

The Craftsman 917.27377 is a robust lawn mower designed to provide homeowners with an efficient and reliable solution for lawn maintenance. Renowned for its durability and user-friendly features, it stands as a testament to Craftsman’s commitment to quality.

One of the standout features of the 917.27377 is its powerful engine. Equipped with a 17.5 HP Briggs & Stratton engine, it delivers ample power for tackling tough grass, ensuring that both small yards and larger lawns are easily managed. The engine is also designed for easy starting, minimizing the frustration often associated with mower maintenance.

The cutting deck of the Craftsman 917.27377 measures 42 inches, allowing for a wide cutting path that reduces mowing time. This size is particularly advantageous for homeowners with moderately-sized lawns, providing a balance between maneuverability and efficiency. The deck is constructed with robust materials that ensure longevity while featuring a reinforced washout port for easy cleaning after use, which helps maintain optimal performance.

Another characteristic that sets the Craftsman 917.27377 apart is its adjustable cutting height, which offers a range from 1.5 inches to 4 inches. This flexibility allows homeowners to customize their mowing experience based on the season and grass type, promoting a healthier lawn. The mower also features an easy-to-use lever that allows for quick adjustments without needing any tools.

Technologically, the Craftsman 917.27377 stands out with its automatic transmission, providing smooth and effortless speed adjustments as you mow. This feature enhances user experience, particularly in varying terrain, since the mower can easily adapt to inclines and declines.

Comfort is also a priority in the design of the Craftsman 917.27377. It includes a plush seating area with an ergonomic design that helps reduce fatigue during extended use. The operator's controls are strategically positioned, making them easily accessible to enhance safety and convenience while mowing.

In conclusion, the Craftsman 917.27377 is an impressive lawn mower combining power, versatility, and comfort. Its reliable engine, generous cutting deck, adjustable height settings, and user-friendly technology make it an ideal choice for homeowners seeking to maintain their lawns with ease and efficiency. The Craftsman 917.27377 exemplifies the brand's dedication to delivering high-quality lawn care products that meet the needs of various users.
Top Page Image Contents