Craftsman 917.27377 HOW to USE Your Tractor, To SET Parking Brake, To Move Forward and Backward

Page 13

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

HOW TO USE YOUR TRACTOR

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

1.Depress clutch/brake pedal all the way down and hold.

2.Pull parking brake lever up and release pressure from clutch/brake pedal. Pedal should remain in brake position.

Make sure parking brake will hold trac- tor secure.

Attachment Clutch Lever

Position

Choke

inition Key

,"Disengaged"

Thr_Position

/ Parking Brake

"Engaged"

Position

"Disengaged"

"Brake"

Lever

Position

Position

 

STOPPING

MOWER BLADES -

• To stop mower blades, move attachment clutch lever to "DISENGAGED" position.

GROUND DRIVE -

•To stop ground drive, depress clutch/ brake pedal all the way down.

•Move gearshift lever to neutral (N) position.

ENGINE -

•Move throttle control to slow position. NOTE: Failure to move throttle control

to slow position and allowing engine to

idle before stopping may cause engine to "backfire".

•Turn ignition key to "STOP" position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

•Never use choke to stop engine.

IMPORTANT: Leaving the ignition switch in any position other than "STOP" will

cause the battery to discharge and go dead.

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause "browning" of grass. To eliminate this possibility, always stop engine when

_:_opping tractor on grass areas. CAUTION: Always stop tractor com-

pletely, as described above, before leaving the operator's position.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

•Operating engine at less than full

throttle reduces the battery charging rate.

•Full throttle offers the best bagging and mower performance.

TO USE CHOKE CONTROL

Use choke control whenever you are start- ing a cold engine. Do not use to start a warm engine.

•To engage choke control, pull knob out. Slowly push knob in to disengage.

TO MOVE FORWARD AND BACKWARD

The direction and speed of movement is controlled by the gearshift lever.

1.Start tractor with clutch/brake pedal de- pressed and gearshift lever in neutral

(N)position.

2.Move gearshift lever to desired po- sition.

3.Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle.

TO ADJUST MOWER CUTTING HEIGHT

The position of the attachment lift lever determines the cutting height.

•Grasp lift lever.

•Press plunger with thumb and move lever to desired position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Icrrftsmrni Limited Warranty on Battery Limited Warranty on Craftsman Riding EquipmentGeneral Operation Do not IV. ServicePage Sears Installation Service Product SpecificationsCustomer Responsibilities Repair Protection AgreementsSeat Steering WheelKeys Slope Sheet Tools Required for Assembly Howto SET UP Your TractorTo Remove Tractor from Before Removing Tractor from Skid Attach Steering WheelTo Rolltractor OFF Skid See Install SeatIf previously removed Install Mulcher PlateCheck Deck Levelness Check for Proper Position of ALL Belts@@@@@ Attachment Clutch Lever Used Know Your TractorTo SET Parking Brake HOW to USE Your TractorTo Move Forward and Backward To Stop Mower Blades To Adjust Gauge WheelsTo Operate On HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start EngineMulching Mowing Tips Mowing TipsGeneral Recommendations ChartBefore Each USE LubricationBlade Removal TractorTo Sharpen Blade To Clean Battery and Terminals BatteryEngine Transaxle CoolingClean AIR INTAKE/COOLING Areas Clean AIR ScreenAIR Filter IN-LINE Fuel FilterTo Install Mower CleaningTractor To Remove MowerSIDE-TO-SIDE Adjustment To Level Mower HousingTo Check and Adjust Brake Belt InstallationTo Adjust Brake To Check BrakeFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEU- Tral AdjustmentTo Start Engine with a Weak BAT- TE RY Replacing BatteryTo Attach Jumper Cables Interlocks and RelaysTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Remove mower from tractor for winter BatteryFuel System Engine OILIgnition switch Troubleshooting ChartCause Correction Problem Cause Problem Cause Correction RED01115BLACK Tractor - Model Number SchematicTractor - Model Number Electrical KEY Part Description Tractor -- Model Number 917.273770 Chassis and Enclosures 175710 Pivot Bracket Tractor -- Model Number Ground Drive X .1845/1865 Tractor -- Model Number Steering Steering Tractor -- Model Number Engine 137180 KEY Part Tractor -- Model Number Seat Assembly186388 Tractor -- Model Number DecalsTractor -- Model Number Lift Assembly Tractor -- Model Number Lift Assembly Tractor -- Model Number Mower Deck 1o6 1o2 1o3losOnly 35A Teeth 523 51B 20@ 220 798 697890 Screw Suggested Guide for Sighting Slopes for Safe Operation 6E/A R,. o 4,0

917.27377 specifications

The Craftsman 917.27377 is a robust lawn mower designed to provide homeowners with an efficient and reliable solution for lawn maintenance. Renowned for its durability and user-friendly features, it stands as a testament to Craftsman’s commitment to quality.

One of the standout features of the 917.27377 is its powerful engine. Equipped with a 17.5 HP Briggs & Stratton engine, it delivers ample power for tackling tough grass, ensuring that both small yards and larger lawns are easily managed. The engine is also designed for easy starting, minimizing the frustration often associated with mower maintenance.

The cutting deck of the Craftsman 917.27377 measures 42 inches, allowing for a wide cutting path that reduces mowing time. This size is particularly advantageous for homeowners with moderately-sized lawns, providing a balance between maneuverability and efficiency. The deck is constructed with robust materials that ensure longevity while featuring a reinforced washout port for easy cleaning after use, which helps maintain optimal performance.

Another characteristic that sets the Craftsman 917.27377 apart is its adjustable cutting height, which offers a range from 1.5 inches to 4 inches. This flexibility allows homeowners to customize their mowing experience based on the season and grass type, promoting a healthier lawn. The mower also features an easy-to-use lever that allows for quick adjustments without needing any tools.

Technologically, the Craftsman 917.27377 stands out with its automatic transmission, providing smooth and effortless speed adjustments as you mow. This feature enhances user experience, particularly in varying terrain, since the mower can easily adapt to inclines and declines.

Comfort is also a priority in the design of the Craftsman 917.27377. It includes a plush seating area with an ergonomic design that helps reduce fatigue during extended use. The operator's controls are strategically positioned, making them easily accessible to enhance safety and convenience while mowing.

In conclusion, the Craftsman 917.27377 is an impressive lawn mower combining power, versatility, and comfort. Its reliable engine, generous cutting deck, adjustable height settings, and user-friendly technology make it an ideal choice for homeowners seeking to maintain their lawns with ease and efficiency. The Craftsman 917.27377 exemplifies the brand's dedication to delivering high-quality lawn care products that meet the needs of various users.
Top Page Image Contents