Craftsman 917.27377 manual To Level Mower Housing, SIDE-TO-SIDE Adjustment

Page 22

6.Connectanti-swaybar to chassis bracketand securewith retainerspring.

7.Push clutch cablehousingguide into bracket,slide collar onto guide and securewith largeretainerspring.

8.Placeflat washerand clutchspring on idlerpulley bolt and securewith small retainerspring.

9.Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure

tires are properly inflated (See "PROD- UCT SPECIFICATIONS" section of this

manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of

mower to ground. Distance "A" on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjust- ment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut

will change mower height about 1/8".

• Recheck measurements after adjusting.

Bottom edge

Bottom edge of

of mower to _ v_

n3o_er to ground

0roond

l/

Gr oundLin ee

Suspension Arm

Lift Link Nut_

Adjustment

FRONT-TO-BACK ADJUSTMENT IMPORTANT: Deck must be level side-to side. If the following front-to-back adjust- ment is necessary, be sure to adjust both

front links equally so mower will stay level side-to-side.

To obtain the best cutting results, the mower housing should be adjusted so

that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in

its highest position.

Check adjustment on right side of trac- tor. Measure distance "D" directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjust- ments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut "E"

on both front links an equal number of turns.

When distance "D" is 1/8" to 1/2"

lower at front than rear, tighten nuts "F" against trunnion on both front links.

To raise front of mower, loosen nut "F" from trunnion on both front links. Tighten

nut "E" on both front links an equal num- ber of turns. The two front links must

remain equal in length.

When distance "D" is 1/8" to 1/2" lower

at front than rear, tighten nut "F" against trunnion on both front links.

Recheck side-to-side adjustment.

Both Front Links Should be Equal in Length

=t"E"

mru

Front Links

TO REPLACE MOWER BLADE DRIVE

BELT

The mower blade drive belt may be re- placed without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

1.Remove mower from tractor (See "TO REMOVE MOWER" in this section of

manual).

22

Image 22
Contents Icrrftsmrni Limited Warranty on Craftsman Riding Equipment Limited Warranty on BatteryGeneral Operation IV. Service Do notPage Customer Responsibilities Product SpecificationsSears Installation Service Repair Protection AgreementsSeat Steering WheelKeys Slope Sheet To Remove Tractor from Howto SET UP Your TractorTools Required for Assembly Before Removing Tractor from Skid Attach Steering WheelInstall Seat To Rolltractor OFF Skid SeeCheck Deck Levelness Install Mulcher PlateIf previously removed Check for Proper Position of ALL Belts@@@@@ Know Your Tractor Attachment Clutch Lever UsedTo SET Parking Brake HOW to USE Your TractorTo Move Forward and Backward To Operate To Adjust Gauge WheelsTo Stop Mower Blades On HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start EngineMowing Tips Mulching Mowing TipsBefore Each USE ChartGeneral Recommendations LubricationBlade Removal TractorTo Sharpen Blade Engine BatteryTo Clean Battery and Terminals Transaxle CoolingAIR Filter Clean AIR ScreenClean AIR INTAKE/COOLING Areas IN-LINE Fuel FilterTractor CleaningTo Install Mower To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Adjust Brake Belt InstallationTo Check and Adjust Brake To Check BrakeTransaxle Gear Shift Lever NEU- Tral Adjustment Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables Replacing BatteryTo Start Engine with a Weak BAT- TE RY Interlocks and RelaysTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor Fuel System BatteryRemove mower from tractor for winter Engine OILIgnition switch Troubleshooting ChartCause Correction Problem Cause Problem Cause Correction Tractor - Model Number Schematic RED01115BLACKTractor - Model Number Electrical KEY Part Description Tractor -- Model Number 917.273770 Chassis and Enclosures 175710 Pivot Bracket Tractor -- Model Number Ground Drive X .1845/1865 Tractor -- Model Number Steering Steering Tractor -- Model Number Engine 137180 Tractor -- Model Number Seat Assembly KEY PartTractor -- Model Number Decals 186388Tractor -- Model Number Lift Assembly Tractor -- Model Number Lift Assembly 1o6 1o2 1o3los Tractor -- Model Number Mower DeckOnly 35A Teeth 523 51B 20@ 220 798 697890 Screw Suggested Guide for Sighting Slopes for Safe Operation 6E/A R,. o 4,0

917.27377 specifications

The Craftsman 917.27377 is a robust lawn mower designed to provide homeowners with an efficient and reliable solution for lawn maintenance. Renowned for its durability and user-friendly features, it stands as a testament to Craftsman’s commitment to quality.

One of the standout features of the 917.27377 is its powerful engine. Equipped with a 17.5 HP Briggs & Stratton engine, it delivers ample power for tackling tough grass, ensuring that both small yards and larger lawns are easily managed. The engine is also designed for easy starting, minimizing the frustration often associated with mower maintenance.

The cutting deck of the Craftsman 917.27377 measures 42 inches, allowing for a wide cutting path that reduces mowing time. This size is particularly advantageous for homeowners with moderately-sized lawns, providing a balance between maneuverability and efficiency. The deck is constructed with robust materials that ensure longevity while featuring a reinforced washout port for easy cleaning after use, which helps maintain optimal performance.

Another characteristic that sets the Craftsman 917.27377 apart is its adjustable cutting height, which offers a range from 1.5 inches to 4 inches. This flexibility allows homeowners to customize their mowing experience based on the season and grass type, promoting a healthier lawn. The mower also features an easy-to-use lever that allows for quick adjustments without needing any tools.

Technologically, the Craftsman 917.27377 stands out with its automatic transmission, providing smooth and effortless speed adjustments as you mow. This feature enhances user experience, particularly in varying terrain, since the mower can easily adapt to inclines and declines.

Comfort is also a priority in the design of the Craftsman 917.27377. It includes a plush seating area with an ergonomic design that helps reduce fatigue during extended use. The operator's controls are strategically positioned, making them easily accessible to enhance safety and convenience while mowing.

In conclusion, the Craftsman 917.27377 is an impressive lawn mower combining power, versatility, and comfort. Its reliable engine, generous cutting deck, adjustable height settings, and user-friendly technology make it an ideal choice for homeowners seeking to maintain their lawns with ease and efficiency. The Craftsman 917.27377 exemplifies the brand's dedication to delivering high-quality lawn care products that meet the needs of various users.