Craftsman 917.27103 To Remove Wheel FOR-REPAIRS, To Start Engine That has a Weak Battery

Page 25

TO REMOVE WHEEL FOR-REPAIRS

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not

lose).

° Repair tire and reassemble.

,On rear wheels only: align grooves in rear wheel hub and axleo Insert square

key.

•Replace washers and snap retaining ring securely in axle groove.

o Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to stow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining Ring

Axle

TO START ENGINE THAT HAS A WEAK BATTERY

_kCAUTION: Lead-acid batteries gener* ate explosive gases. Keep sparks, flame and smoking materials away from batter-

ies. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged, If "jumper cables" are used for emergency starting, follow this procedure:

IMPORTANT: Your tractor is equipped with a 12 volt negative grounded system. The other vehicle must also be a 12 volt

negative grounded system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

°Connect each end of the RED cable to the POSITIVE (+) terminal of each bat-

tery, taking care not to short against chassis.

o Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery,

TO REMOVE CABLES, REVERSE ORDER -

o Remove BLACK cable first from chassis

and then from the fully charged battery. o Remove RED cable last from both bat-

terieso

Positive Terminal

Negative Terminal

Charged

BatteryNegative

PositiveTerminal

Terminal

TO REPLACE HEADLIGHT BULB

°Raise hood°

o Pull bulb holder out of the hole in the backside of the grill.

o Replace bulb in holder and push bulb holder securely back into the hole in the

backside of the grill. o Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or pre- vent it from starting.

o Check widng. See electrical wiring dia- gram in the Repair Parts section of this manual.

TO REPLACE FUSE

Replace with 30 amp automotive-type

plug-in fuse, The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL AS- SEMBLY

• Raise hood.

o Unsnap headlight wire connector.

°Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

°To replace, reverse above procedures.

N

Headlight Wire _ctor

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Lawn Limited 90 DAY Warranty on Battery Limited TWO Year Warranty on Craftsman Riding EquipmentGeneral Operation Slope Operation ServiceDo not ChildrenGrass can hide obstacles TY is InvolvedMaintenance Agreement Product SpecificationsCustomer Responsibilities #10 Seat Assemble Extension Shaft and Boot Tools Required for AssemblyInstall Steering Wheel To Remove Tractor from Carton Unpack CartonConnect Battery HOW to SET UP Your TractorInstall Seat Check Deck Levelness Install Mulcher PlateCheck for Proper Position ALL Belts Check Brake SystemAssemble Gauge Wheels to Mower Deck ChecklistKeep Area Clearslope Hazards Know Your Tractor Stopping To SET Parking BrakeTo Transport To Operate MowerAttachments Before Starting the Engine Check Engine OIL LevelWarm WEATHERSTARTING50 F and Above To Start EngineCold Weather Starting 50 F and below Mowing TipsImportant For best performance, keep Mulching Mowing TipsChart Customer Responsibilities MaintenanceBefore Each USE Brake Operation TractorTires AIR Filter BeltsClean AIR INTAKE/COOLING Areas To Service CartridgeEngine OIL Filter MufflerTo Remove Mower To Install MowerTo Replace Mower Blade Drive To Level Mower HousingTo Adjust Brake BeltinstallationTo Adjust Steering Wheel Align Ment To Replace Motion Drive BeltTo Remove Wheel FOR-REPAIRS To Start Engine That has a Weak BatteryTo Replace Headlight Bulb To Adjust Carburetor To Adjust Throttle ControlEngine CableFuel System EngineEngine OIL Problem Cause ChartUnderside of mower hous Problem Cause CorrectionProblem Troubleshooting ChartCorrection ATT-CLUTC SchematicTractor - Model Number 1o... i,, rr NO. NO.DESCRIPTION ElectricalTractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number 917.271030 Chassis and EnclosuresTractor -- Model Number Ground Drive KEY Part Description Tractor -- Model Number Ground Drive= = Tractor --MODEL Number Steering AssemblyTractor - Model Number Steering Assembly Engine Optional EquipmentKEY Part EngineKEY Seat AssemblyDecals KEY Part TRACTOR-- Model NumberTractor -- Model Number LiFT AssemblyTractor - Model Number Lift AssemblyTRACTOR--MODEL Number Mower Deck KEY Part NO. no Description Mower DeckTractor - Model Number Dana Transaxle - Model Number Part KEY Description Tractor -- Model Number Dana Transaxle - Model NumberKcas Crankcase KEY Part NO. NO.DESCRIPTION Cylinder HEAD/VALVE!BREATHER KEY Part NO. NO.DESCRIPTIONTo2 NO, no Starting System Engine Controls KEY Part NO. NO.DESCRIPTIONIll ill illlll Exhaust Fuel System Crankshaft KEY Part DescriptionPage Page Page Suggested Guide for SaGHTING Slopes for Safe OPERATaON 800=366=PART

917.27103 specifications

The Craftsman 917.27103 is a robust lawn tractor designed to meet the needs of both residential and light commercial users. With a focus on performance, comfort, and durability, this machine stands out in the crowded market of lawn care equipment.

One of the key features of the Craftsman 917.27103 is its powerful engine. Equipped with a reliable 19.5 HP Briggs & Stratton engine, this lawn tractor delivers exceptional power and efficiency. The engine is designed for easy starting and maintenance, ensuring that users can get to work quickly without complications. Complementing this power is a hydrostatic transmission that provides seamless speed adjustments without the need for manual gear changes, allowing for smooth operation while navigating various terrains.

Another significant characteristic of the Craftsman 917.27103 is its cutting deck. Featuring a 42-inch cutting deck, this lawn tractor ensures a generous cutting width, allowing users to cover large areas more efficiently. The deck is adjustable, enabling four different cutting heights to accommodate various grass types and lawn conditions. The inclusion of a side discharge, mulching, and bagging capabilities provides added versatility, allowing users to choose their preferred method of grass disposal.

Comfort is also a primary consideration in the design of the Craftsman 917.27103. The tractor features an ergonomic seat with high back support, ensuring that users can work longer without discomfort. An easy-to-use dashboard with straightforward controls enables users to operate the tractor without confusion.

Durability is enhanced by the tractor's steel frame and robust construction, which can withstand the rigors of regular use. The wheels are designed with a deep tread pattern, providing excellent traction on various surfaces, whether it be wet grass, sandy soil, or sloping lawns.

In terms of technology, the Craftsman 917.27103 offers several innovative features. A maintenance-free battery adds convenience, while an integrated fuel gauge allows users to monitor fuel levels with ease. The compact design ensures that it fits into tight storage spaces, making it ideal for homeowners with limited garage areas.

Overall, the Craftsman 917.27103 is a versatile and dependable lawn tractor, combining power, comfort, and durability in a user-friendly package. Whether for residential gardening or light commercial landscaping tasks, it meets the demands of users looking to achieve a well-manicured lawn with ease.
Top Page Image Contents