Craftsman 917.27077 manual To Start Engine with a Weak Battery, To Adjust Steering Wheel Align

Page 24

TRANSAXLE SHIFTER LINKAGE AND ADJUSTMENT

The transaxle should be in neutral when

the gear shift lever is in the neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjust- ment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

•Loosen two Iocknuts on tie red.

•Tum center rod until gearshift lever falls into neutral lock gate on fender console.

•Tighten Iocknuts securely.

Gearshift Lever

Neutral Lock

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

Washers

Retaining

Ring

__Gate

Locknuts

Transaxle

TO ADJUST STEERING WHEEL ALIGN-

MENT

If steering wheel crossbars are not hori- zontal (left to right) when wheels are posi-

tioned straight forward, remove steering wheel and reassemble per instructions in

the Assembly section of this manual.

FRONTWHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

Axle Cover

'_

(Rear Wheel Only)

TO START ENGINE WITH A WEAK BATTERY

_CAUTION: Lead-acid batteries gener- ate explosive gases. Keep sparks, flame and smoking materials away from batter-

ies. Always wear eye protection when around batteries.

If your battery is too weak to start the

engine, it should be recharged. (See "BATTERY" in the MAINTANCE section of

this manual).

If "jumper cables" are used for emergency starting, follow this procedure: IMPORTANT: Your tractor Is equipped with a 12 volt negative grounded system. The other vehicle must also be a 12 volt negative grounded system. Do not use your tractor battery to start other vehicles.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each bat-

tery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery

•Connect the other end of the BLACK cable to good CHASSIS GROUND, away from fuel tank and battery

TO REMOVE CABLES, REVERSE ORDER

•BLACK cable first from chassis and then from the fully charged battery

•RED cable last from both batteries

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents RRIIFTSMIIN Limi Warraniy on Craftsman Riding Equipment General OperationService ChildrenSlope Operation Do notNevermakeadjustmentsor repairswith the enginerunning TY is InvolvedProduct Specifications Maintenance AgreementCustomer Responsibilities Parts BAG Contents Shown Full Size @@ , Washers Assemble Extension Shaft and Boot Install Steering WheelTools Required for To Remove Tractor from CartonHOW to SET UP Your Tractor Connect Battery Install SeatInstall Mulcher Plate Assemble Gauge Wheels to Mower DeckCheck for Proper Position of ALL Belts H L Attachment HOW to USE Your Tractor To SET Parking BrakeStopping EngineToadjustmowercuttingheight Towing Carts and Other AttachmentsBefore Starting Engine ADD Gasoline To Start EngineWarm Weather Starting 50 F Above Cold Weather Starting 50 F and belowMowing Tips Mulching Mowing TipsLubrication Chart General RecommendationsBefore Each USE Tractor BrakeoperationTransaxle Cooling EngineCleaning To Install Mower To Remove MowerTolevelmowerhousing FRONT-TO-BACK AdjustmentSIDE-TO-SIDE Adjustment Belt RemovalTo Adjust Brake Am NutTo Start Engine with a Weak Battery To Adjust Steering Wheel AlignReplacing Battery To Adjust Throttle Control CableTo Adjust Choke Control To Adjust Carburetor Preliminary SettingFinal SEI-IING Acceleration TestTractor Fuel SystemEngine OIL CylindersTroubleshooting Chart ProblemCause Correction Problemcause Troubleshootinghart Problem Cause Correction=FAST Schematic Tractor - Model NumberTractor - Model Number ElectricalTractor - Model Number ElectricalTractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number Ground Drive Tractor - Model Number Ground Drive KEY Part NO. no DescriptionTractor - Model Number Steering Assembly Tractor - Model Number 917,270770 Steering Assembly KEY Part NO. NO. DescriptionEngine Engine KEY Part NO. NO. Description 12 STD522507 Bolt RrHex 1/4Tractor - Model Number Seat Assembly KEY -PART NO. noDecals KEYWheels & Tires Part DESCRIP11ONTractor - Model Number Lift Assembly KEY Part Description Tractor - Model Number Mower Deck KEY Part Description Stlt150 792077A 535 Gasket SET J Tractor o Model Number Label Kiti 51A 281412 Spacer, Carburetor Inch= 25.4 mm 859 Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Sears

917.27077 specifications

The Craftsman 917.27077 is a versatile and powerful garden tractor designed for homeowners who seek performance, reliability, and ease of use in their lawn care equipment. Engineered with a robust build and advanced technologies, it caters to a wide range of outdoor tasks, from mowing to hauling.

One of the standout features of the Craftsman 917.27077 is its 24-horsepower Kohler engine. This powerful engine delivers the necessary torque for efficient cutting and handling of various terrains, making it suitable for both flat lawns and hilly landscapes. The reliable engine is known for its longevity and low maintenance requirements, ensuring that homeowners can rely on it for many seasons.

Another significant aspect of the 917.27077 is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and mowing efficiency, allowing users to cover substantial ground while easily navigating through tight spaces and around obstacles. Equipped with cutting height adjustments, the deck can be set to different positions, providing flexibility for achieving the desired grass height.

The garden tractor also features a hydrostatic transmission, which offers smooth and user-friendly operation. Unlike traditional gear systems, hydrostatic transmissions allow for seamless speed and direction changes without the need to shift gears. This functionality enhances user comfort, especially during lengthy mowing sessions, making the Craftsman 917.27077 an excellent choice for homeowners.

In terms of characteristics, the Craftsman 917.27077 is designed with an ergonomic seat that ensures comfort during use. The adjustable seat can accommodate various user heights, ensuring a comfortable grip on the steering wheel for optimal control. Additionally, the tractor features a user-friendly control panel with intuitive controls for easy operation.

Another noteworthy feature is the built-in mulching capability. This technology allows for the grass clippings to be finely chopped and returned to the lawn as natural fertilizer, promoting a healthier grass ecosystem. This not only saves time but also reduces waste, making it an environmentally friendly choice.

Overall, the Craftsman 917.27077 exemplifies a well-rounded garden tractor that combines power, comfort, and innovative technology. Whether tackling routine lawn maintenance or more demanding landscape tasks, this garden tractor provides reliability and performance that homeowners can depend on. Its user-friendly features and advanced characteristics make it a valuable addition to any outdoor toolkit.
Top Page Image Contents