Craftsman 917.27077 Replacing Battery, To Adjust Throttle Control Cable, To Adjust Choke Control

Page 25

"Pos=t=ve"(+)

Negative ( )

REPLACING BATTERY

_CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch

bands,rings,etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to posi- tive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely.

•Close terminal access doom.

•Close hood.

Hex

Terminal

Access ._';_.;::{"

Red)

Cable

Negative

Cable

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor t6 run poorly, stop running, or pre- vent it from starting.

•Check wiring. See electrical widng dia- gram in the Repair Parts section.

TO REPLACE FUSE

Replace with 30 amp automotive-type

plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at

sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedures.

Headlight

Wire Connector

ENGINE

Maintenance, repair, or replacement of the emission control devices and systems, which are being done at the customers

expense, may be performed by any non- road engine repair establishment or indi- vidual. Warranty repairs must be per-

formed by an authorized engine manufac- turer'sservice outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

•With engine not running, move throttle control lever to fast position;

•Check that swivel is against side of quarter circle. If it is not, loosen cable clamp screw and pull cable back until swivel is against quarter circle. Tighten

cable clamp screw securely.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be nec- essary. Check adjustment as described below before loosening cable. If adjust- ment is necessary, proceed as follows:

•With engine not running, move choke control (located on dash panel) to full choke position.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents RRIIFTSMIIN General Operation Limi Warraniy on Craftsman Riding EquipmentChildren ServiceSlope Operation Do notTY is Involved Nevermakeadjustmentsor repairswith the enginerunningMaintenance Agreement Product SpecificationsCustomer Responsibilities Parts BAG Contents Shown Full Size @@ , Washers Install Steering Wheel Assemble Extension Shaft and BootTools Required for To Remove Tractor from CartonInstall Seat HOW to SET UP Your Tractor Connect BatteryInstall Mulcher Plate Assemble Gauge Wheels to Mower DeckCheck for Proper Position of ALL Belts H L Attachment To SET Parking Brake HOW to USE Your TractorStopping EngineTowing Carts and Other Attachments ToadjustmowercuttingheightBefore Starting Engine To Start Engine ADD GasolineWarm Weather Starting 50 F Above Cold Weather Starting 50 F and belowMulching Mowing Tips Mowing TipsGeneral Recommendations Lubrication ChartBefore Each USE Brakeoperation TractorEngine Transaxle CoolingCleaning To Remove Mower To Install MowerFRONT-TO-BACK Adjustment TolevelmowerhousingSIDE-TO-SIDE Adjustment Belt RemovalAm Nut To Adjust BrakeTo Adjust Steering Wheel Align To Start Engine with a Weak BatteryTo Adjust Throttle Control Cable Replacing BatteryTo Adjust Choke Control Preliminary Setting To Adjust CarburetorFinal SEI-IING Acceleration TestFuel System TractorEngine OIL CylindersProblem Troubleshooting ChartCause Correction Problemcause Correction Troubleshootinghart Problem Cause=FAST Tractor - Model Number SchematicElectrical Tractor - Model NumberElectrical Tractor - Model NumberTractor - Model Number Chassis and Enclosures KEY Part NO. NO.DESCRIPTION Tractor - Model Number Ground Drive KEY Part NO. no Description Tractor - Model Number Ground DriveTractor - Model Number Steering Assembly KEY Part NO. NO. Description Tractor - Model Number 917,270770 Steering AssemblyEngine 12 STD522507 Bolt RrHex 1/4 Engine KEY Part NO. NO. DescriptionKEY -PART NO. no Tractor - Model Number Seat AssemblyKEY DecalsWheels & Tires Part DESCRIP11ONTractor - Model Number Lift Assembly KEY Part Description Tractor - Model Number Mower Deck Stlt KEY Part Description150 792077A 535 Gasket SET J Tractor o Model Number Label Kiti 51A 281412 Spacer, Carburetor Inch= 25.4 mm 859 Page Page Page Suggested Guide for Sighting Slopes for Safe Operation Sears

917.27077 specifications

The Craftsman 917.27077 is a versatile and powerful garden tractor designed for homeowners who seek performance, reliability, and ease of use in their lawn care equipment. Engineered with a robust build and advanced technologies, it caters to a wide range of outdoor tasks, from mowing to hauling.

One of the standout features of the Craftsman 917.27077 is its 24-horsepower Kohler engine. This powerful engine delivers the necessary torque for efficient cutting and handling of various terrains, making it suitable for both flat lawns and hilly landscapes. The reliable engine is known for its longevity and low maintenance requirements, ensuring that homeowners can rely on it for many seasons.

Another significant aspect of the 917.27077 is its 42-inch cutting deck. This size strikes a perfect balance between maneuverability and mowing efficiency, allowing users to cover substantial ground while easily navigating through tight spaces and around obstacles. Equipped with cutting height adjustments, the deck can be set to different positions, providing flexibility for achieving the desired grass height.

The garden tractor also features a hydrostatic transmission, which offers smooth and user-friendly operation. Unlike traditional gear systems, hydrostatic transmissions allow for seamless speed and direction changes without the need to shift gears. This functionality enhances user comfort, especially during lengthy mowing sessions, making the Craftsman 917.27077 an excellent choice for homeowners.

In terms of characteristics, the Craftsman 917.27077 is designed with an ergonomic seat that ensures comfort during use. The adjustable seat can accommodate various user heights, ensuring a comfortable grip on the steering wheel for optimal control. Additionally, the tractor features a user-friendly control panel with intuitive controls for easy operation.

Another noteworthy feature is the built-in mulching capability. This technology allows for the grass clippings to be finely chopped and returned to the lawn as natural fertilizer, promoting a healthier grass ecosystem. This not only saves time but also reduces waste, making it an environmentally friendly choice.

Overall, the Craftsman 917.27077 exemplifies a well-rounded garden tractor that combines power, comfort, and innovative technology. Whether tackling routine lawn maintenance or more demanding landscape tasks, this garden tractor provides reliability and performance that homeowners can depend on. Its user-friendly features and advanced characteristics make it a valuable addition to any outdoor toolkit.
Top Page Image Contents