Craftsman 486.24515 owner manual Spacer Tube Wheel, Flat, TWASHER HUB CAP CoI-rER PIN

Page 9

Assemble the front tongue over the top of the rear tongue using three 3/8" x 3" hex bolts, 3/8" lock washers and 3/8" hex lock nuts. See figure 8.

(3)3/8" x 3"

TONGUE _,/HEX BOLTS

(REAR)

_

TONGUE

(3)

WASHERS_'-_-.-.(3) 3/8" HEX

LOCK NUTS

FIGURE 8

Assemble the hitch bracket to the front tongue using "' two 3/8" x 1-1/4" hex bolts, 3/8" lock washers and 3/8" hex nuts. Tighten. See figure 9.

3/8" x 1-1/4"

_

HITCH BRACKET

..

HEX BOLT

"'"_1

/

 

.

 

 

 

 

3/8

LOCK

_"_I_

TONGUE

 

WAS H ER _..._........_

/

 

LOCK

NUT---_

 

 

 

FIGURE 9

Assemble the latch lock assembly to the tongue using two 1/4" x 2-3/4" hex bolts, two 1/4" lock washers and two 1/4" hex nuts. Fasten to the two front holes in the forward grouping of four holes as shown in figure 10.

Assemble the angle stop to the tongue using two 1/4" x 2-3/4" hex bolts, two 1/4" lock washers and two 1/4" hex nuts. Fasten to the two front holes in the rear

grouping of four holes as shown in figure 10.

 

HE)( BOLT

ANGLE

LATCH LOCK

 

ASS'Y.

 

TONGUE

1/4" LOCK

WASHER

WASHER

1/4" HEX

 

 

NUT

FIGURE 10

 

Position the tongue on the bottom of the cart as shown in figure 11. Assemble the axle through the wheel support and the tongue. Fasten the axle to the wheel support using two 1/4" x 1-3/4" hex bolts and 1/4" hex nuts (SEMS). Tighten.

IMPORTANT: Make sure the tongue is securely locked to the latch stand bracket by the latch lock assembly.

1/4" x 1-3/4"

HEX BOLT

AXLE

"_

(DRAW BAR)

TONGUE

114" HEX

NUT (SEMS)

FIGURE 11

Assemble a spacer tube onto each end of the axle as shown in figure 12.

Assemble a flat washer, a wheel (valve stem facing out), and another flat washer onto the axle as

shown in figure 12. Secure the wheel with a cotter pin, spreading the ends so that a hub cap can fit

over the pin. Assemble the hub cap by pressing it onto the flat washer. Repeat on other end of axle.

SPACER TUBE

WHEEL

FLAT

WASHER

\

FLAT

tWASHER

HUB CAP CoI-rER PIN

FIGURE 12

Image 9
Contents Irrftsmrn Limited Oneyear Warranty on Slopes To Avoid Serious Injury Not Shown Full Size GAE Hardware Package ChipperVac Carton Qty DescriptionLockwasher, 3/8 Side Panel L.H Ref. Qty. Description Front Panel15 2 Hose Clamp 16 1 Tongue Rear 18 1 Hitch Bracket 19 1 Adapter BracketAssembling the Chipper VAC Removal of Parts from CartonHEX NUT Sems HEX BoltLatch Stand Bracket Leave Holes Open forHEX Bolts Wheel SupportSpacer Tube Wheel FlatTWASHER HUB CAP CoI-rER PIN Cross Lock WasherX 3/4 Brace HEX BoltFront ClampHE Bolt Door Bracket Cross BRACE. DoorWeldedangles WasherWeld Bolts NylonRubber TIE Strap HoseHitch PINKey Qty. Description Assembly of the Deck Adapter #62468 to the Mower DeckNot Shown Full Size From FrontAdapter Bracket Use existing holes or drill 5/16 diameter hole or holes4- H£X Deck Adapter Mower DeckIylon Washer For 1990 and Newer Murray Tractors with a 38 or 40 DeckMounting Strap Lock NUTKnow Your Chipper VAC HOW to Start Your Chipper VAC HOW to Stop Your Chipper VACHOW to USE Your Chipper VAC Before StartingUsing the Chipper Chute Engine Maintenance Check Soft Vinyl BootCleaning Before Each USE Check for Loose FastenersHEX Lock Nuts Sharpening or Replacing Chipper BladesChanges Slows considerably Or compositionofPart QTY Description 4121 Deflector, Exhaust not shown Hitch BracketAv= liable only With item no Liable only With item no43262 43064Nut, Hex Jam 5/16-18 Thd Washer, Lock 5/16 Spring Blade-ChipperClip, Retaining Pin Page Page Page SIGInAND Holdthis Level with a Verticaltree