Craftsman 486.24515 For 1990 and Newer Murray Tractors with a 38 or 40 Deck, Iylon Washer

Page 16

FOR 1990 AND NEWER MURRAY

TRACTORS WITH A 38" OR 40" DECK

Cut out two templates and place on deck adapter as shown in figure 34. Tape smaller one on top and larger one on the side and bottom. After they are in place, carefully mark around the templates, then cut out adapter to obtain correct opening.

Bolt end of mounting strap to the 5/16" bolt on the mower deck. The other end of the strap will bolt to a hole in the deck adapter, which must be drilled. Position the adapter on the deck, then drill a 5/16" hole in the bottom of the adapter that will align with the hole in the strap. Fasten the adapter to the strap using a 1/4" x 3/4" hex bolt, 1/4" fiat washer, nylon washer and 1/4" hex nut. See figure 34.

38"/40" TEMPLATE

TEMPLATE TO CUT OUT SLOT

 

CUT OUT SLOT IN TOP

 

OF DECK ADAPTER

 

1/4" x 3/4" HE_ BOLT

 

1/4" FLAT WASHER

 

_IYLONWASHER

 

"MOUNTING STRAP

BOLTTHIS END OF

1/4" LOCK NUT

STRAP TO 5/16" BOLT

 

ON MOWER DECK

 

FIGURE 34

 

FOR 1990 AND NEWER MURRAY

TRACTORS WITH A 46" DECK

•Tape 46" template onto deck adapter. Mark and then cut out adapter.

Fasten the angle bracket and the mounting bracket to the mower deck as shown in figure 35. Use two 5/16" x 3/4" carriage belts, 5/16" flat washers and 5/16"

lock nuts. The bolt heads go on inside of mower deck.

Drill two 5/16" diameter holes in the deck adapter that will align with the holes in the angle bracket and the mounting bracket. Assemble the deck adapter to both brackets using two 1/4" x 3/4" hex bolts, 1/4" flat washers, nylon washers and 1/4" lock nuts. See figure 35.

\. /

ANGLE BRACKET

NYLON WASHER

_

MOUNTING

1/4" FLAT

1/4" x 3/4"

NYLON WASHER

1/

1/4" x 3/4" HEX BOLT-_-,--%_

FIGURE 35

• Assemble end of hose and hose clamp over the round

Assemble end of hose and hose clamp over

the round

opening of deck adapter and tighten clamp. GO

opening of deck adapter and tighten

clamp.

GO

DIRECTLY TO THE OPERATION INSTRUCTIONS

DIRECTLY TO THE OPERATION

INSTRUCTIONS

WHICH ARE LOCATED ON PAGE 17,

WHICH ARE LOCATED ON PAGE

17.

 

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Irrftsmrn Limited Oneyear Warranty on Slopes To Avoid Serious Injury Hardware Package ChipperVac Carton Qty Description Not Shown Full Size GAELockwasher, 3/8 Ref. Qty. Description Front Panel Side Panel L.H15 2 Hose Clamp 16 1 Tongue Rear 18 1 Hitch Bracket 19 1 Adapter BracketRemoval of Parts from Carton Assembling the Chipper VACHEX NUT Sems HEX BoltLeave Holes Open for Latch Stand BracketHEX Bolts Wheel SupportFlat Spacer Tube WheelTWASHER HUB CAP CoI-rER PIN Lock Washer CrossX 3/4 Brace HEX BoltClamp FrontHE Bolt Door Bracket Cross BRACE. DoorWasher WeldedanglesWeld Bolts NylonHose Rubber TIE StrapHitch PINAssembly of the Deck Adapter #62468 to the Mower Deck Key Qty. DescriptionNot Shown Full Size From FrontUse existing holes or drill 5/16 diameter hole or holes Adapter Bracket4- H£X Deck Adapter Mower DeckFor 1990 and Newer Murray Tractors with a 38 or 40 Deck Iylon WasherMounting Strap Lock NUTKnow Your Chipper VAC HOW to Stop Your Chipper VAC HOW to Start Your Chipper VACHOW to USE Your Chipper VAC Before StartingUsing the Chipper Chute Check Soft Vinyl Boot Engine MaintenanceCleaning Before Each USE Check for Loose FastenersSharpening or Replacing Chipper Blades HEX Lock NutsSlows considerably Or compositionof ChangesPart QTY Description 4121 Hitch Bracket Deflector, Exhaust not shownAv= liable only With item no Liable only With item no43064 43262Nut, Hex Jam 5/16-18 Thd Blade-Chipper Washer, Lock 5/16 SpringClip, Retaining Pin Page Page Page SIGInAND Holdthis Level with a Verticaltree
Top Page Image Contents