Weed Eater SGT18H46C To Adjust Gauge Wheels See Fig, To Operate on Hills, To Transport See Figs

Page 13
With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 8)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

GUAGE WHEEL

MOUNTING

BRACKET

3/8-16

LOCKNUT

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 8

TO OPERATE MOWER (See Fig. 9)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 6 and 10)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

 

"ENGAGED" POSITION

 

ATTACHMENT

 

LIFT LEVER

 

HIGH POSITION

 

LOW

ATTACHMENT

POSITION

 

CLUTCH LEVER

 

"DISENGAGED"

DEFLECTOR

POSITION

SHIELD

 

FIG. 9

FIG. 10

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Model NO. SGT18H46C IV. Service Safety RulesGeneral Operation II. Slope OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Unassembled PartsGauge Wheels Slope SheetTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level See Fig Before Starting the EngineADD Gasoline To Start Engine See FigPurge Transmission Mowing TipsGeneral Recommendations Customer ResponsibilitiesBefore Each USE Tractor Engine AIR Filter CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILTroubleshooting Points OFF Service Notes Tractor - Model Number SGT18H46C Schematic2122 Electrical178446 108423X178861 Chassis 176554 174620175710 74780612Drive 74760648 165936175461 175556Steering Assembly 177883 175122175146 175118Engine 176252 176174 Control, ThrottleSeat Assembly Wheels & Tires Decals178387 Mower Lift 175689 Mower Deck 175746 17060612175747 178342Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

SGT18H46C specifications

The Weed Eater SGT18H46C is a robust and efficient lawn mower that is designed for homeowners seeking a reliable machine to maintain their yards with ease. This model stands out for its powerful performance and user-friendly features that make lawn care a stress-free experience.

At the heart of the SGT18H46C is its 18-horsepower engine, which provides ample power to tackle a wide variety of grass types and terrain. This engine is designed for durability and efficiency, helping to ensure that you can rely on it for many mowing seasons to come. The mower offers a smooth ride with its hydrostatic transmission, allowing for seamless speed adjustments without the need for clutching or shifting gears. This feature makes it user-friendly, especially for those new to lawn care.

One of the standout characteristics of the SGT18H46C is its cutting deck, which measures 46 inches. This wide deck enables users to cover more ground in less time, ultimately speeding up the mowing process. The deck is made from durable materials that can withstand the rigors of regular use, and the design allows for a clean and precise cut. Additionally, it features adjustable cutting heights, ranging from 1.5 to 4 inches, providing versatility to cater to various grass types and seasons.

Another significant feature is the mower's ability to mulch clippings. With this function, users can recycle grass clippings back into the lawn, promoting healthy growth and reducing yard waste.

The SGT18H46C is also equipped with a comfortable seat and ergonomic controls, making it easy to operate for extended periods. The cutting deck is designed to allow for easy maintenance, with an accessible washout port that simplifies cleaning after mowing.

The unit's compact design ensures easy maneuverability, even in tight spaces, enhancing its usability for smaller lawns. Its strong construction is complemented by a warranty that provides peace of mind to buyers, ensuring that they are protected against manufacturing defects.

In summary, the Weed Eater SGT18H46C offers homeowners a powerful, efficient, and user-friendly lawn care solution. With its impressive engine, durable construction, and thoughtful design features, it is an excellent choice for those looking to maintain a beautiful lawn with minimal effort. Whether you have a large yard or a modest landscape, the SGT18H46C is up to the task.
Top Page Image Contents