Weed Eater SGT18H46C manual Mowing Tips, Purge Transmission

Page 15

OPERATION

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run- ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have devel- oped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

•Place tractor safely on level surface with engine off and parking brake set.

•Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

•Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

•Engage transmission by placing freewheel control in driving position (See “TO TRANSPORT” in this section of manual).

•Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

•Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

•Your tractor is now purged and now ready for normal operation.

MOWING TIPS

•Tire chains cannot be used when the mower housing is attached to tractor.

•Mower should be properly leveled for best mowing performance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

•The left hand side of mower should be used for trimming.

•Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the tractor. This will result in a more even distribution of clippings and more uniform cutting.

•When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 11 ).

•If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

•Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

•Always operate engine at full throttle when mowing to assure better mowing performance and proper dis- charge of material. Regulate ground speed by selecting a low enough gear to give the mower cutting perfor- mance as well as the quality of cut desired.

•When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

FIG. 11

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. SGT18H46C II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Slope Sheet Unassembled PartsSteering Wheel Gauge WheelsTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD GasolinePurge Transmission Mowing TipsCustomer Responsibilities General RecommendationsBefore Each USE Tractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Service Notes Tractor - Model Number SGT18H46C Schematic2122 Electrical108423X 178446178861 Chassis 74780612 174620176554 175710Drive 175556 16593674760648 175461Steering Assembly 175118 175122177883 175146Engine 176252 176174 Control, ThrottleSeat Assembly Decals Wheels & Tires178387 Mower Lift 175689 Mower Deck 178342 17060612175746 175747Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

SGT18H46C specifications

The Weed Eater SGT18H46C is a robust and efficient lawn mower that is designed for homeowners seeking a reliable machine to maintain their yards with ease. This model stands out for its powerful performance and user-friendly features that make lawn care a stress-free experience.

At the heart of the SGT18H46C is its 18-horsepower engine, which provides ample power to tackle a wide variety of grass types and terrain. This engine is designed for durability and efficiency, helping to ensure that you can rely on it for many mowing seasons to come. The mower offers a smooth ride with its hydrostatic transmission, allowing for seamless speed adjustments without the need for clutching or shifting gears. This feature makes it user-friendly, especially for those new to lawn care.

One of the standout characteristics of the SGT18H46C is its cutting deck, which measures 46 inches. This wide deck enables users to cover more ground in less time, ultimately speeding up the mowing process. The deck is made from durable materials that can withstand the rigors of regular use, and the design allows for a clean and precise cut. Additionally, it features adjustable cutting heights, ranging from 1.5 to 4 inches, providing versatility to cater to various grass types and seasons.

Another significant feature is the mower's ability to mulch clippings. With this function, users can recycle grass clippings back into the lawn, promoting healthy growth and reducing yard waste.

The SGT18H46C is also equipped with a comfortable seat and ergonomic controls, making it easy to operate for extended periods. The cutting deck is designed to allow for easy maintenance, with an accessible washout port that simplifies cleaning after mowing.

The unit's compact design ensures easy maneuverability, even in tight spaces, enhancing its usability for smaller lawns. Its strong construction is complemented by a warranty that provides peace of mind to buyers, ensuring that they are protected against manufacturing defects.

In summary, the Weed Eater SGT18H46C offers homeowners a powerful, efficient, and user-friendly lawn care solution. With its impressive engine, durable construction, and thoughtful design features, it is an excellent choice for those looking to maintain a beautiful lawn with minimal effort. Whether you have a large yard or a modest landscape, the SGT18H46C is up to the task.
Top Page Image Contents