Weed Eater SGT18H46C To Adjust Throttle Control Cable, To Replace Headlight Bulb, To Replace Fuse

Page 24

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Fig. 29)

CAUTION: Do not short battery termi- nals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 30)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

FIG. 30

ENGINE

Maintenance, repair, or replacement of the emission control

KEPS NUT

TERMINAL ACCESS DOOR

TERMINAL

GUARD

HEX BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

devices and systems, which are being done at the custom- ers expense, may be performed by any non-road engine repair establishment or individual. Warranty repairs must be performed by an authorized engine manufacturer's service outlet.

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is

FIG. 29

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

necessary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, see engine manual.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjust- ment should not be necessary. However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Model NO. SGT18H46C Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering WheelGauge Wheels Slope SheetAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionCustomer Responsibilities General RecommendationsBefore Each USE Tractor Engine Cleaning AIR FilterMuffler Spark PlugsService and Adjustments To Install MowerTo Level Mower Housing To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Adjust Brake See Fig To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig Transmission REMOVAL/REPLACEMENT To Adjust Steering Wheel AlignmentFront Wheel TOE-IN/CAMBER To Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points OFF Service Notes Schematic Tractor - Model Number SGT18H46CElectrical 2122108423X 178446178861 Chassis 174620 176554175710 74780612Drive 165936 74760648175461 175556Steering Assembly 175122 177883175146 175118Engine 176174 Control, Throttle 176252Seat Assembly Decals Wheels & Tires178387 Mower Lift 175689 Mower Deck 17060612 175746175747 178342Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

SGT18H46C specifications

The Weed Eater SGT18H46C is a robust and efficient lawn mower that is designed for homeowners seeking a reliable machine to maintain their yards with ease. This model stands out for its powerful performance and user-friendly features that make lawn care a stress-free experience.

At the heart of the SGT18H46C is its 18-horsepower engine, which provides ample power to tackle a wide variety of grass types and terrain. This engine is designed for durability and efficiency, helping to ensure that you can rely on it for many mowing seasons to come. The mower offers a smooth ride with its hydrostatic transmission, allowing for seamless speed adjustments without the need for clutching or shifting gears. This feature makes it user-friendly, especially for those new to lawn care.

One of the standout characteristics of the SGT18H46C is its cutting deck, which measures 46 inches. This wide deck enables users to cover more ground in less time, ultimately speeding up the mowing process. The deck is made from durable materials that can withstand the rigors of regular use, and the design allows for a clean and precise cut. Additionally, it features adjustable cutting heights, ranging from 1.5 to 4 inches, providing versatility to cater to various grass types and seasons.

Another significant feature is the mower's ability to mulch clippings. With this function, users can recycle grass clippings back into the lawn, promoting healthy growth and reducing yard waste.

The SGT18H46C is also equipped with a comfortable seat and ergonomic controls, making it easy to operate for extended periods. The cutting deck is designed to allow for easy maintenance, with an accessible washout port that simplifies cleaning after mowing.

The unit's compact design ensures easy maneuverability, even in tight spaces, enhancing its usability for smaller lawns. Its strong construction is complemented by a warranty that provides peace of mind to buyers, ensuring that they are protected against manufacturing defects.

In summary, the Weed Eater SGT18H46C offers homeowners a powerful, efficient, and user-friendly lawn care solution. With its impressive engine, durable construction, and thoughtful design features, it is an excellent choice for those looking to maintain a beautiful lawn with minimal effort. Whether you have a large yard or a modest landscape, the SGT18H46C is up to the task.
Top Page Image Contents