Weed Eater SGT18H46C Before Starting the Engine, Check Engine OIL Level See Fig, ADD Gasoline

Page 14

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 15)

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

ADD GASOLINE

•Fill fuel tank. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW 32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

WARNING: Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

CAUTION: Fill to bottom of gas tank filler neck. Do not overfill. Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

TO START ENGINE (See Fig. 6)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm- up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Model NO. SGT18H46C General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Gauge Wheels Unassembled PartsSteering Wheel Slope SheetHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig To Attach Nose Roller See FigInstall Mower and Drive Belt See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsADD Gasoline Before Starting the EngineCheck Engine OIL Level See Fig To Start Engine See FigMowing Tips Purge TransmissionBefore Each USE Customer ResponsibilitiesGeneral Recommendations Tractor Engine Muffler CleaningAIR Filter Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower To Remove Mower See FigFRONT-TO-BACK Adjustment See Figs To Replace Mower Drive BeltTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig Front Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment To Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points OFF Service Notes Schematic Tractor - Model Number SGT18H46CElectrical 2122178861 108423X178446 Chassis 175710 174620176554 74780612Drive 175461 16593674760648 175556Steering Assembly 175146 175122177883 175118Engine 176174 Control, Throttle 176252Seat Assembly 178387 DecalsWheels & Tires Mower Lift 175689 Mower Deck 175747 17060612175746 178342Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

SGT18H46C specifications

The Weed Eater SGT18H46C is a robust and efficient lawn mower that is designed for homeowners seeking a reliable machine to maintain their yards with ease. This model stands out for its powerful performance and user-friendly features that make lawn care a stress-free experience.

At the heart of the SGT18H46C is its 18-horsepower engine, which provides ample power to tackle a wide variety of grass types and terrain. This engine is designed for durability and efficiency, helping to ensure that you can rely on it for many mowing seasons to come. The mower offers a smooth ride with its hydrostatic transmission, allowing for seamless speed adjustments without the need for clutching or shifting gears. This feature makes it user-friendly, especially for those new to lawn care.

One of the standout characteristics of the SGT18H46C is its cutting deck, which measures 46 inches. This wide deck enables users to cover more ground in less time, ultimately speeding up the mowing process. The deck is made from durable materials that can withstand the rigors of regular use, and the design allows for a clean and precise cut. Additionally, it features adjustable cutting heights, ranging from 1.5 to 4 inches, providing versatility to cater to various grass types and seasons.

Another significant feature is the mower's ability to mulch clippings. With this function, users can recycle grass clippings back into the lawn, promoting healthy growth and reducing yard waste.

The SGT18H46C is also equipped with a comfortable seat and ergonomic controls, making it easy to operate for extended periods. The cutting deck is designed to allow for easy maintenance, with an accessible washout port that simplifies cleaning after mowing.

The unit's compact design ensures easy maneuverability, even in tight spaces, enhancing its usability for smaller lawns. Its strong construction is complemented by a warranty that provides peace of mind to buyers, ensuring that they are protected against manufacturing defects.

In summary, the Weed Eater SGT18H46C offers homeowners a powerful, efficient, and user-friendly lawn care solution. With its impressive engine, durable construction, and thoughtful design features, it is an excellent choice for those looking to maintain a beautiful lawn with minimal effort. Whether you have a large yard or a modest landscape, the SGT18H46C is up to the task.
Top Page Image Contents