Weed Eater SGT18H46C manual Install Seat See Fig, To Attach Nose Roller See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard packing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

FLAT WASHER

ADJUSTMENT

KNOB

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section page 11 for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place freewheel control in freewheeling position to disengage transmission (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

TO DRIVE TRACTOR OFF SKID (See Opera- tion section page 11 for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been completed.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" po- sition.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine. After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "OFF" position.

Continue with the instructions that follow.

TO ATTACH NOSE ROLLER (See Fig. 4)

•Position brackets, 17/32 x 7/8 x 16 gauge washers, and nose roller between deck mounting brackets as shown. Be sure to position brackets on correct side, as shown.

•Install hex bolts and lock nuts as shown. Tighten hardware securely.

NOTE: Be sure bracket tabs are positioned in tab holes in deck brackets.

TAB

“A” BRACKET

HOLE

TAB

NOSE ROLLER

 

HEX

 

BOLT

 

“B”

LOCK NUT

 

BRACKET

TAB

WASHER

FIG. 4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. SGT18H46C II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Slope Sheet Unassembled PartsSteering Wheel Gauge WheelsTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorTo Attach Nose Roller See Fig Install Seat See FigInstall Mower and Drive Belt See Figs Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate on Hills To Operate Mower See FigTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level See Fig ADD GasolinePurge Transmission Mowing TipsGeneral Recommendations Customer ResponsibilitiesBefore Each USE Tractor Engine Spark Plugs CleaningAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower HousingTo Replace Mower Drive Belt FRONT-TO-BACK Adjustment See FigsTo Replace Mower Blade Drive Belt See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment Transmission REMOVAL/REPLACEMENTFront Wheel TOE-IN/CAMBER To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Service Notes Tractor - Model Number SGT18H46C Schematic2122 Electrical178446 108423X178861 Chassis 74780612 174620176554 175710Drive 175556 16593674760648 175461Steering Assembly 175118 175122177883 175146Engine 176252 176174 Control, ThrottleSeat Assembly Wheels & Tires Decals178387 Mower Lift 175689 Mower Deck 178342 17060612175746 175747Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation

SGT18H46C specifications

The Weed Eater SGT18H46C is a robust and efficient lawn mower that is designed for homeowners seeking a reliable machine to maintain their yards with ease. This model stands out for its powerful performance and user-friendly features that make lawn care a stress-free experience.

At the heart of the SGT18H46C is its 18-horsepower engine, which provides ample power to tackle a wide variety of grass types and terrain. This engine is designed for durability and efficiency, helping to ensure that you can rely on it for many mowing seasons to come. The mower offers a smooth ride with its hydrostatic transmission, allowing for seamless speed adjustments without the need for clutching or shifting gears. This feature makes it user-friendly, especially for those new to lawn care.

One of the standout characteristics of the SGT18H46C is its cutting deck, which measures 46 inches. This wide deck enables users to cover more ground in less time, ultimately speeding up the mowing process. The deck is made from durable materials that can withstand the rigors of regular use, and the design allows for a clean and precise cut. Additionally, it features adjustable cutting heights, ranging from 1.5 to 4 inches, providing versatility to cater to various grass types and seasons.

Another significant feature is the mower's ability to mulch clippings. With this function, users can recycle grass clippings back into the lawn, promoting healthy growth and reducing yard waste.

The SGT18H46C is also equipped with a comfortable seat and ergonomic controls, making it easy to operate for extended periods. The cutting deck is designed to allow for easy maintenance, with an accessible washout port that simplifies cleaning after mowing.

The unit's compact design ensures easy maneuverability, even in tight spaces, enhancing its usability for smaller lawns. Its strong construction is complemented by a warranty that provides peace of mind to buyers, ensuring that they are protected against manufacturing defects.

In summary, the Weed Eater SGT18H46C offers homeowners a powerful, efficient, and user-friendly lawn care solution. With its impressive engine, durable construction, and thoughtful design features, it is an excellent choice for those looking to maintain a beautiful lawn with minimal effort. Whether you have a large yard or a modest landscape, the SGT18H46C is up to the task.
Top Page Image Contents