Weed Eater 186391 Before Starting the Engine, To Operate on Hills To Transport, ADD Gasoline

Page 12

OPERATION

TO OPERATE MOWER (See Fig. 6)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

Select desired height of cut.

Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LE-

VER HIGH POSITION

LOW

POSITION

ATTACHMENT CLUTCH LEVER "DISENGAGED" POSITION

DEFLECTOR

SHIELD

FIG. 6

TO OPERATE ON HILLS

TO TRANSPORT

Raise attachment lift to highest position with attachment lift control.

When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACH- MENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

Check engine oil with tractor on level ground.

Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

• Choose the slowest speed before starting up or down hills.

• Avoid stopping or changing speed on hills.

• If slowing is necessary, move throttle control lever to slower position.

• If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

• Move gearshift lever to 1st gear. Be sure you have allowed room for tractor to roll slightly as you restart movement.

• To restart movement, slowly release parking brake and clutch/brake pedal.

• Make all turns slowly.

12

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

Image 12
Contents Model NO. WET1338A Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Operate on Hills To TransportTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips To Start Engine See FigMaintenance Lubrication ChartGeneral Recommendations Before Each USETractor Brake OperationTires Operator Presence SystemBattery EngineBelts Transaxle CoolingClean AIR Screen Engine Cooling Fins See FigAIR Filter See Fig Cleaning MufflerSpark Plugs IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust Steering Wheel Align MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET1338AElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Decals Wheels & TiresMower Lift Repair Parts Mower Deck 134148 CABService Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWeedeater

186391 specifications

The Weed Eater 186391 is an essential tool for anyone looking to maintain a beautifully manicured lawn or garden. Known for its reliability and user-friendly design, this string trimmer caters to both amateur gardeners and seasoned professionals. One of the standout features of the Weed Eater 186391 is its lightweight construction, making it easy to maneuver around tight corners and navigate through uneven terrain. Weighing in at just over 10 pounds, users can enjoy an extended trimming session without experiencing excessive fatigue.

Equipped with a powerful 25cc 2-cycle engine, the Weed Eater 186391 delivers exceptional cutting power. This engine not only allows it to tackle thick weeds and overgrown grass but also ensures consistent performance across various gardening tasks. Its engine technology emphasizes fuel efficiency and reduced emissions, aligning with today's environmental awareness while still providing robust power for any trimming needs.

The trimmer features a bump head line feed system, which allows users to easily extend the cutting line by simply tapping the head on the ground. This hassle-free approach enhances productivity, ensuring that the job is completed smoothly and efficiently. Additionally, the 18-inch cutting width allows for broader swaths of grass and weeds to be cleared with each pass, significantly reducing the time and effort required for maintenance.

One of the notable characteristics of the Weed Eater 186391 is its ergonomic design. The handle is specifically crafted for optimal comfort, reducing strain on the hands and arms while in use. The adjustable handle height caters to users of various heights, ensuring a comfortable grip regardless of your stature.

Moreover, the Weed Eater 186391 emphasizes safety features, such as a protective guard that shields the user from debris during operation. Its easy-to-access fuel system allows for quick refueling, minimizing downtime between jobs.

In conclusion, the Weed Eater 186391 combines power, efficiency, and comfort, making it an outstanding choice for those looking for a reliable string trimmer. Its innovative design and advanced technology promise exceptional performance, making garden care an enjoyable and efficient task. With the Weed Eater 186391, maintaining your outdoor space has never been easier or more effective.