Weed Eater 186391 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 27)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT

WIRE

CONNECTOR

01536

FIG. 27

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 28)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

With engine not running, move throttle control lever from slow to choke position. Slowly move lever from choke to fast position.

Check that hole in throttle lever and hole in plate line up. If holes “A” are not aligned, loosen clamp screw and move throttle cable until holes are aligned.Tighten clamp screw securely.

TO ADJUST CARBURETOR

The carburetor has been preset at the factory and adjustment should not be necessary.However, minor adjustment may be required to compensate for differences in fuel, temperature, altitude or load. If the carburetor does need adjustment, see engine manual.

High speed stop is factory adjusted. Do not adjust - dam- age may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED.OVERSPEEDINGTHE ENGINE ABOVETHE FACTORY HIGH SPEED SETTING CAN BE DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACTYOUR NEAREST AUTHORIZED SERVICE CENTER/ DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND EXPERIENCE TO MAKE ANY NECESSARY ADJUSTMENTS.

 

IDLE SPEED SCREW

PLATE

 

 

THROTTLE CABLE

 

CLAMP

 

SCREW

 

HOLE “A”

THROTTLE LE-

 

VER

FAST

FIG. 28

23

Image 23
Contents Model NO. WET1338A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig HOW to SET UP Your TractorInstall Seat See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsAIR Filter See Fig Clean AIR ScreenEngine Cooling Fins See Fig IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Check and Adjust Brake See FigTo Adjust Steering Wheel Align Ment To Replace Motion Drive Belt See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET1338A SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB 134148Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWeedeater

186391 specifications

The Weed Eater 186391 is an essential tool for anyone looking to maintain a beautifully manicured lawn or garden. Known for its reliability and user-friendly design, this string trimmer caters to both amateur gardeners and seasoned professionals. One of the standout features of the Weed Eater 186391 is its lightweight construction, making it easy to maneuver around tight corners and navigate through uneven terrain. Weighing in at just over 10 pounds, users can enjoy an extended trimming session without experiencing excessive fatigue.

Equipped with a powerful 25cc 2-cycle engine, the Weed Eater 186391 delivers exceptional cutting power. This engine not only allows it to tackle thick weeds and overgrown grass but also ensures consistent performance across various gardening tasks. Its engine technology emphasizes fuel efficiency and reduced emissions, aligning with today's environmental awareness while still providing robust power for any trimming needs.

The trimmer features a bump head line feed system, which allows users to easily extend the cutting line by simply tapping the head on the ground. This hassle-free approach enhances productivity, ensuring that the job is completed smoothly and efficiently. Additionally, the 18-inch cutting width allows for broader swaths of grass and weeds to be cleared with each pass, significantly reducing the time and effort required for maintenance.

One of the notable characteristics of the Weed Eater 186391 is its ergonomic design. The handle is specifically crafted for optimal comfort, reducing strain on the hands and arms while in use. The adjustable handle height caters to users of various heights, ensuring a comfortable grip regardless of your stature.

Moreover, the Weed Eater 186391 emphasizes safety features, such as a protective guard that shields the user from debris during operation. Its easy-to-access fuel system allows for quick refueling, minimizing downtime between jobs.

In conclusion, the Weed Eater 186391 combines power, efficiency, and comfort, making it an outstanding choice for those looking for a reliable string trimmer. Its innovative design and advanced technology promise exceptional performance, making garden care an enjoyable and efficient task. With the Weed Eater 186391, maintaining your outdoor space has never been easier or more effective.