Weed Eater 186391 manual To Remove Wheel for Repairs See Fig, Replacing Battery See Figs

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 23)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WEAK OR DEAD

 

 

 

 

FULLY CHARGED

BATTERY

 

 

 

 

BATTERY

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FIG. 24

REPLACING BATTERY (See Figs. 25 and 26)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 25

KEPS

TERMINALNUT

COVER

HEX

BOLT

POSITIVE (RED)

NEGATIVE

CABLE

(BLACK) CABLE

 

FIG. 26

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. WET1338A General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigGeneral Recommendations MaintenanceLubrication Chart Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingEngine Cooling Fins See Fig Clean AIR ScreenAIR Filter See Fig Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Align Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET1338AElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Decals Wheels & TiresMower Lift Repair Parts Mower Deck 134148 CABService Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWeedeater

186391 specifications

The Weed Eater 186391 is an essential tool for anyone looking to maintain a beautifully manicured lawn or garden. Known for its reliability and user-friendly design, this string trimmer caters to both amateur gardeners and seasoned professionals. One of the standout features of the Weed Eater 186391 is its lightweight construction, making it easy to maneuver around tight corners and navigate through uneven terrain. Weighing in at just over 10 pounds, users can enjoy an extended trimming session without experiencing excessive fatigue.

Equipped with a powerful 25cc 2-cycle engine, the Weed Eater 186391 delivers exceptional cutting power. This engine not only allows it to tackle thick weeds and overgrown grass but also ensures consistent performance across various gardening tasks. Its engine technology emphasizes fuel efficiency and reduced emissions, aligning with today's environmental awareness while still providing robust power for any trimming needs.

The trimmer features a bump head line feed system, which allows users to easily extend the cutting line by simply tapping the head on the ground. This hassle-free approach enhances productivity, ensuring that the job is completed smoothly and efficiently. Additionally, the 18-inch cutting width allows for broader swaths of grass and weeds to be cleared with each pass, significantly reducing the time and effort required for maintenance.

One of the notable characteristics of the Weed Eater 186391 is its ergonomic design. The handle is specifically crafted for optimal comfort, reducing strain on the hands and arms while in use. The adjustable handle height caters to users of various heights, ensuring a comfortable grip regardless of your stature.

Moreover, the Weed Eater 186391 emphasizes safety features, such as a protective guard that shields the user from debris during operation. Its easy-to-access fuel system allows for quick refueling, minimizing downtime between jobs.

In conclusion, the Weed Eater 186391 combines power, efficiency, and comfort, making it an outstanding choice for those looking for a reliable string trimmer. Its innovative design and advanced technology promise exceptional performance, making garden care an enjoyable and efficient task. With the Weed Eater 186391, maintaining your outdoor space has never been easier or more effective.
Top Page Image Contents