Weed Eater 186391 manual HOW to SET UP Your Tractor, Install Seat See Fig, Check Battery See Fig

Page 7

ASSEMBLY

HOW TO SET UP YOUR TRACTOR

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

LOCK WASHER

02465

ADJUSTMENT

BOLT

FIG. 2

CHECK BATTERY (See Fig. 3)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See “BATTERY” in the Maintenance section of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing clutch/brake pedal.

•Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding deflector shield up against tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Sit on seat in operating position, depress clutch/brake pedal and set the parking brake.

•Place gear shift lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Depress clutch/brake pedal into full "BRAKE" position and hold. Move gearshift lever to 1st gear.

•Slowly release clutch/brake pedal and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place gearshift lever in neutral position.

•Turn ignition key to "OFF" position.

Continue with the instructions that follow.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model NO. WET1338A II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenAIR Filter See Fig IN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Check and Adjust Brake See FigTo Adjust Steering Wheel Align Ment To Replace Motion Drive Belt See FigTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove Wheel for Repairs See FigTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number WET1338A SchematicElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Wheels & Tires DecalsMower Lift Repair Parts Mower Deck CAB 134148Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationWeedeater

186391 specifications

The Weed Eater 186391 is an essential tool for anyone looking to maintain a beautifully manicured lawn or garden. Known for its reliability and user-friendly design, this string trimmer caters to both amateur gardeners and seasoned professionals. One of the standout features of the Weed Eater 186391 is its lightweight construction, making it easy to maneuver around tight corners and navigate through uneven terrain. Weighing in at just over 10 pounds, users can enjoy an extended trimming session without experiencing excessive fatigue.

Equipped with a powerful 25cc 2-cycle engine, the Weed Eater 186391 delivers exceptional cutting power. This engine not only allows it to tackle thick weeds and overgrown grass but also ensures consistent performance across various gardening tasks. Its engine technology emphasizes fuel efficiency and reduced emissions, aligning with today's environmental awareness while still providing robust power for any trimming needs.

The trimmer features a bump head line feed system, which allows users to easily extend the cutting line by simply tapping the head on the ground. This hassle-free approach enhances productivity, ensuring that the job is completed smoothly and efficiently. Additionally, the 18-inch cutting width allows for broader swaths of grass and weeds to be cleared with each pass, significantly reducing the time and effort required for maintenance.

One of the notable characteristics of the Weed Eater 186391 is its ergonomic design. The handle is specifically crafted for optimal comfort, reducing strain on the hands and arms while in use. The adjustable handle height caters to users of various heights, ensuring a comfortable grip regardless of your stature.

Moreover, the Weed Eater 186391 emphasizes safety features, such as a protective guard that shields the user from debris during operation. Its easy-to-access fuel system allows for quick refueling, minimizing downtime between jobs.

In conclusion, the Weed Eater 186391 combines power, efficiency, and comfort, making it an outstanding choice for those looking for a reliable string trimmer. Its innovative design and advanced technology promise exceptional performance, making garden care an enjoyable and efficient task. With the Weed Eater 186391, maintaining your outdoor space has never been easier or more effective.
Top Page Image Contents