Weed Eater 186391 Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

Tire pressure gauge

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO 10-12 FT. LBS TORQUE.

•Place tabs of steering boot over tab slots in dash and push down to secure.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

STEERING

BOOT

WHEEL

 

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

TAB

SLOTS

STEERING

 

SHAFT

 

FIG. 1

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. WET1338A General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigGeneral Recommendations MaintenanceLubrication Chart Before Each USETires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingClean AIR Screen Engine Cooling Fins See FigAIR Filter See Fig Spark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel Align Ment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number WET1338AElectrical KEY Part Description Chassis Repair Parts Drive Transaxle Steering Repair Parts Engine 170864 Control Th/ch Flag Seat Decals Wheels & TiresMower Lift Repair Parts Mower Deck 134148 CABService Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXWeedeater

186391 specifications

The Weed Eater 186391 is an essential tool for anyone looking to maintain a beautifully manicured lawn or garden. Known for its reliability and user-friendly design, this string trimmer caters to both amateur gardeners and seasoned professionals. One of the standout features of the Weed Eater 186391 is its lightweight construction, making it easy to maneuver around tight corners and navigate through uneven terrain. Weighing in at just over 10 pounds, users can enjoy an extended trimming session without experiencing excessive fatigue.

Equipped with a powerful 25cc 2-cycle engine, the Weed Eater 186391 delivers exceptional cutting power. This engine not only allows it to tackle thick weeds and overgrown grass but also ensures consistent performance across various gardening tasks. Its engine technology emphasizes fuel efficiency and reduced emissions, aligning with today's environmental awareness while still providing robust power for any trimming needs.

The trimmer features a bump head line feed system, which allows users to easily extend the cutting line by simply tapping the head on the ground. This hassle-free approach enhances productivity, ensuring that the job is completed smoothly and efficiently. Additionally, the 18-inch cutting width allows for broader swaths of grass and weeds to be cleared with each pass, significantly reducing the time and effort required for maintenance.

One of the notable characteristics of the Weed Eater 186391 is its ergonomic design. The handle is specifically crafted for optimal comfort, reducing strain on the hands and arms while in use. The adjustable handle height caters to users of various heights, ensuring a comfortable grip regardless of your stature.

Moreover, the Weed Eater 186391 emphasizes safety features, such as a protective guard that shields the user from debris during operation. Its easy-to-access fuel system allows for quick refueling, minimizing downtime between jobs.

In conclusion, the Weed Eater 186391 combines power, efficiency, and comfort, making it an outstanding choice for those looking for a reliable string trimmer. Its innovative design and advanced technology promise exceptional performance, making garden care an enjoyable and efficient task. With the Weed Eater 186391, maintaining your outdoor space has never been easier or more effective.
Top Page Image Contents