Weed Eater 96016000100 Service and Adjustments, To Remove Mower See Fig, To Install Mower See Fig

Page 19

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUST- MENTS:

•Depress clutch/brake pedal fully and set parking brake.

•Place gearshift lever in neutral (N) position.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 13)

Mower will be easier to remove from the right side of trac- tor.

•Place attachment clutch in “DISENGAGED” position.

•Move attachment lift lever forward to lower mower to its lowest position.

•Roll belt off engine pulley.

•Remove small retainer spring, and remove clutch spring off pulley bolt.

•Remove large retainer spring, slide collar off and push housing guide out of bracket.

•Disconnect anti-swaybar from chassis bracket by re- moving retainer spring.

•Disconnect suspension arms from rear deck brackets by removing retainer springs.

•Disconnect front links from deck by removing retainer springs.

•Raise lift lever to raise suspension arms. Slide mower out from under tractor.

IMPORTANT: IF AN ATTACHMENT OTHER THAN THE MOWER DECK IS TO BE MOUNTED ON THE TRACTOR, REMOVE THE FRONTLINKSANDHOOKTHECLUTCHSPRINGINTOSQUARE HOLE IN FRAME.

TO INSTALL MOWER (See Fig. 13)

•Raise attachment lift lever to its highest position.

•Slide mower under tractor with deflector shield to right side of tractor.

•Lower lift lever to its lowest position.

•Connect front links to mower deck and secure with retainer springs..

•Connect suspension arms to rear deck brackets and secure with retainer springs.

•Connect anti-swaybar to chassis bracket and secure with retainer spring.

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

 

SMALL

 

 

RETAINER

 

 

SPRING

 

FLAT WASHER

SUSPENSION

 

 

 

CLUTCH SPRING

ARMS

SQUARE HOLE

 

 

 

 

 

ENGINE PULLEY

RETAINER SPRING

 

FRONT LINK

ANTI-SWAY BAR

 

RETAINER SPRINGS

COLLAR

 

(BOTH SIDES)

 

 

HOUSING GUIDE

 

 

LARGE RETAINER

02695

 

SPRING

CLUTCH SPRING

DEFLECTOR SHIELD

 

 

BRACKET

 

 

FIG. 13

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Always Wear EYE Protection During Operation HD13538II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsBlade Removal See Fig TractorTo Sharpen Blade See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

96016000100 specifications

The Weed Eater 96016000100 is a powerful and efficient outdoor tool designed to make lawn care and landscaping tasks easier for homeowners and professionals alike. This gas-powered string trimmer is equipped with advanced features and technologies that enhance its performance, reliability, and user convenience.

One of the standout characteristics of the Weed Eater 96016000100 is its lightweight design, making it easy to maneuver in various terrains and around obstacles. The trimmer weighs just under ten pounds, allowing users to tackle prolonged landscaping jobs without experiencing excessive fatigue. Its well-balanced structure contributes to a comfortable user experience, ensuring that both novice and experienced operators can handle the tool with ease.

The engine of the Weed Eater 96016000100 is a robust 25cc two-stroke engine that delivers powerful performance for effectively trimming grass and weeds. This engine is designed for quick starts and operates smoothly, providing consistent power throughout the trimming process. The combination of its size and capabilities allows users to handle tougher vegetation while maintaining an efficient fuel consumption rate.

One of the most notable features of this string trimmer is its 17-inch cutting swath, which enables users to cover more ground in less time. The trimmer is equipped with a dual-line bump feed system that allows for easy line advancement. By simply bumping the head against the ground, users can release more line, ensuring continuous operation without the need for frequent interruptions to reload the trimmer line.

Durability is another essential characteristic of the Weed Eater 96016000100. It features a solid build that includes a high-quality plastic housing and metal components resistant to wear and tear. This durability ensures the trimmer can withstand the rigors of outdoor use, providing homeowners with a reliable tool for years to come.

Additionally, the ergonomic handle design significantly improves the user experience. The adjustable handle allows for easy height adjustment, accommodating users of different sizes and preferences. The design also helps to reduce vibration, providing added comfort during extended use.

Overall, the Weed Eater 96016000100 emerges as a well-rounded string trimmer that combines performance, durability, and user-friendly features, making it an excellent choice for anyone looking to keep their yard neat and tidy. Whether you're dealing with tall grass, weeds, or edging tasks, this trimmer is equipped to handle it all efficiently.
Top Page Image Contents