Weed Eater 96016000100 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

REPLACING BATTERY (See Figs. 24 and 25)

WARNING: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connect- ing battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acci- dental grounding.

Lift seat pan to raised position.

Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

Install new battery with terminals in same position as old battery.

First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

Raise hood.

Pull bulb holder out of the hole in the backside of the grill.

Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

Raise hood.

Unsnap headlight wire connector.

Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Image 23
Contents Always Wear EYE Protection During Operation HD13538II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport Reverse Operation System ROSTo Operate Mower See Fig To Operate on HillsTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

96016000100 specifications

The Weed Eater 96016000100 is a powerful and efficient outdoor tool designed to make lawn care and landscaping tasks easier for homeowners and professionals alike. This gas-powered string trimmer is equipped with advanced features and technologies that enhance its performance, reliability, and user convenience.

One of the standout characteristics of the Weed Eater 96016000100 is its lightweight design, making it easy to maneuver in various terrains and around obstacles. The trimmer weighs just under ten pounds, allowing users to tackle prolonged landscaping jobs without experiencing excessive fatigue. Its well-balanced structure contributes to a comfortable user experience, ensuring that both novice and experienced operators can handle the tool with ease.

The engine of the Weed Eater 96016000100 is a robust 25cc two-stroke engine that delivers powerful performance for effectively trimming grass and weeds. This engine is designed for quick starts and operates smoothly, providing consistent power throughout the trimming process. The combination of its size and capabilities allows users to handle tougher vegetation while maintaining an efficient fuel consumption rate.

One of the most notable features of this string trimmer is its 17-inch cutting swath, which enables users to cover more ground in less time. The trimmer is equipped with a dual-line bump feed system that allows for easy line advancement. By simply bumping the head against the ground, users can release more line, ensuring continuous operation without the need for frequent interruptions to reload the trimmer line.

Durability is another essential characteristic of the Weed Eater 96016000100. It features a solid build that includes a high-quality plastic housing and metal components resistant to wear and tear. This durability ensures the trimmer can withstand the rigors of outdoor use, providing homeowners with a reliable tool for years to come.

Additionally, the ergonomic handle design significantly improves the user experience. The adjustable handle allows for easy height adjustment, accommodating users of different sizes and preferences. The design also helps to reduce vibration, providing added comfort during extended use.

Overall, the Weed Eater 96016000100 emerges as a well-rounded string trimmer that combines performance, durability, and user-friendly features, making it an excellent choice for anyone looking to keep their yard neat and tidy. Whether you're dealing with tall grass, weeds, or edging tasks, this trimmer is equipped to handle it all efficiently.