Weed Eater 96016000100 To Check and Adjust Brake See Fig, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

IDLER PULLEYS

MANDREL PULLEYS

FIG. 18

TO CHECK AND ADJUST BRAKE (See Fig. 19)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Place gear shift lever in neutral (N) position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-1/2", loosen jam nut and turn nut “A” until distance becomes 1-1/2". Retighten jam nut against nut “A”.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

1-1/2"

NUT “A”

JAM NUT

OPERATING ARM

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

CENTER SPAN

KEEPER

TRANSAXLE

PULLEY

FIG. 20

FIG. 19

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation HD13538Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Reverse Operation System ROSTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

96016000100 specifications

The Weed Eater 96016000100 is a powerful and efficient outdoor tool designed to make lawn care and landscaping tasks easier for homeowners and professionals alike. This gas-powered string trimmer is equipped with advanced features and technologies that enhance its performance, reliability, and user convenience.

One of the standout characteristics of the Weed Eater 96016000100 is its lightweight design, making it easy to maneuver in various terrains and around obstacles. The trimmer weighs just under ten pounds, allowing users to tackle prolonged landscaping jobs without experiencing excessive fatigue. Its well-balanced structure contributes to a comfortable user experience, ensuring that both novice and experienced operators can handle the tool with ease.

The engine of the Weed Eater 96016000100 is a robust 25cc two-stroke engine that delivers powerful performance for effectively trimming grass and weeds. This engine is designed for quick starts and operates smoothly, providing consistent power throughout the trimming process. The combination of its size and capabilities allows users to handle tougher vegetation while maintaining an efficient fuel consumption rate.

One of the most notable features of this string trimmer is its 17-inch cutting swath, which enables users to cover more ground in less time. The trimmer is equipped with a dual-line bump feed system that allows for easy line advancement. By simply bumping the head against the ground, users can release more line, ensuring continuous operation without the need for frequent interruptions to reload the trimmer line.

Durability is another essential characteristic of the Weed Eater 96016000100. It features a solid build that includes a high-quality plastic housing and metal components resistant to wear and tear. This durability ensures the trimmer can withstand the rigors of outdoor use, providing homeowners with a reliable tool for years to come.

Additionally, the ergonomic handle design significantly improves the user experience. The adjustable handle allows for easy height adjustment, accommodating users of different sizes and preferences. The design also helps to reduce vibration, providing added comfort during extended use.

Overall, the Weed Eater 96016000100 emerges as a well-rounded string trimmer that combines performance, durability, and user-friendly features, making it an excellent choice for anyone looking to keep their yard neat and tidy. Whether you're dealing with tall grass, weeds, or edging tasks, this trimmer is equipped to handle it all efficiently.
Top Page Image Contents