Weed Eater 96016000100 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(1) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEELSTEERING BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HD13538 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

96016000100 specifications

The Weed Eater 96016000100 is a powerful and efficient outdoor tool designed to make lawn care and landscaping tasks easier for homeowners and professionals alike. This gas-powered string trimmer is equipped with advanced features and technologies that enhance its performance, reliability, and user convenience.

One of the standout characteristics of the Weed Eater 96016000100 is its lightweight design, making it easy to maneuver in various terrains and around obstacles. The trimmer weighs just under ten pounds, allowing users to tackle prolonged landscaping jobs without experiencing excessive fatigue. Its well-balanced structure contributes to a comfortable user experience, ensuring that both novice and experienced operators can handle the tool with ease.

The engine of the Weed Eater 96016000100 is a robust 25cc two-stroke engine that delivers powerful performance for effectively trimming grass and weeds. This engine is designed for quick starts and operates smoothly, providing consistent power throughout the trimming process. The combination of its size and capabilities allows users to handle tougher vegetation while maintaining an efficient fuel consumption rate.

One of the most notable features of this string trimmer is its 17-inch cutting swath, which enables users to cover more ground in less time. The trimmer is equipped with a dual-line bump feed system that allows for easy line advancement. By simply bumping the head against the ground, users can release more line, ensuring continuous operation without the need for frequent interruptions to reload the trimmer line.

Durability is another essential characteristic of the Weed Eater 96016000100. It features a solid build that includes a high-quality plastic housing and metal components resistant to wear and tear. This durability ensures the trimmer can withstand the rigors of outdoor use, providing homeowners with a reliable tool for years to come.

Additionally, the ergonomic handle design significantly improves the user experience. The adjustable handle allows for easy height adjustment, accommodating users of different sizes and preferences. The design also helps to reduce vibration, providing added comfort during extended use.

Overall, the Weed Eater 96016000100 emerges as a well-rounded string trimmer that combines performance, durability, and user-friendly features, making it an excellent choice for anyone looking to keep their yard neat and tidy. Whether you're dealing with tall grass, weeds, or edging tasks, this trimmer is equipped to handle it all efficiently.
Top Page Image Contents