Weed Eater 96016000100 manual Transaxle Gear Shift Lever NEUTRAL- Adjustment See Fig

Page 22

SERVICE AND ADJUSTMENTS

TRANSAXLE GEAR SHIFT LEVER NEUTRAL- ADJUSTMENT (See Fig. 21)

The transaxle should be in neutral when the gear shift lever is in neutral (N) (lock gate) position. The adjustment is preset at the factory; however, if adjustment is needed, proceed as follows:

•Make sure transaxle is in neutral (N).

NOTE: When the tractor rear wheels move freely, the transaxle is in neutral.

•Loosen adjustment bolt in front of the right rear wheel.

•Position the gear shift lever in the neutral (N) posi- tion.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

NEUTRAL

LOCK GATE

GEARSHIFT LEVER

ADJUSTMENT

BOLT

FIG. 21

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 22)

RETAINING WASHERS

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 22

TO START ENGINE WITH A WEAK BATTERY (See Fig. 23)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

FIG. 23

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents HD13538 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Reverse Operation System ROSTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

96016000100 specifications

The Weed Eater 96016000100 is a powerful and efficient outdoor tool designed to make lawn care and landscaping tasks easier for homeowners and professionals alike. This gas-powered string trimmer is equipped with advanced features and technologies that enhance its performance, reliability, and user convenience.

One of the standout characteristics of the Weed Eater 96016000100 is its lightweight design, making it easy to maneuver in various terrains and around obstacles. The trimmer weighs just under ten pounds, allowing users to tackle prolonged landscaping jobs without experiencing excessive fatigue. Its well-balanced structure contributes to a comfortable user experience, ensuring that both novice and experienced operators can handle the tool with ease.

The engine of the Weed Eater 96016000100 is a robust 25cc two-stroke engine that delivers powerful performance for effectively trimming grass and weeds. This engine is designed for quick starts and operates smoothly, providing consistent power throughout the trimming process. The combination of its size and capabilities allows users to handle tougher vegetation while maintaining an efficient fuel consumption rate.

One of the most notable features of this string trimmer is its 17-inch cutting swath, which enables users to cover more ground in less time. The trimmer is equipped with a dual-line bump feed system that allows for easy line advancement. By simply bumping the head against the ground, users can release more line, ensuring continuous operation without the need for frequent interruptions to reload the trimmer line.

Durability is another essential characteristic of the Weed Eater 96016000100. It features a solid build that includes a high-quality plastic housing and metal components resistant to wear and tear. This durability ensures the trimmer can withstand the rigors of outdoor use, providing homeowners with a reliable tool for years to come.

Additionally, the ergonomic handle design significantly improves the user experience. The adjustable handle allows for easy height adjustment, accommodating users of different sizes and preferences. The design also helps to reduce vibration, providing added comfort during extended use.

Overall, the Weed Eater 96016000100 emerges as a well-rounded string trimmer that combines performance, durability, and user-friendly features, making it an excellent choice for anyone looking to keep their yard neat and tidy. Whether you're dealing with tall grass, weeds, or edging tasks, this trimmer is equipped to handle it all efficiently.
Top Page Image Contents