HOW to Stop Your Unit, Operating Position

thetic oil is recommended. (A 40:1 ratio is ob- tained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). When mixing fuel fol- low the instructions printed on the container. Always read and follow the safety rules under

FUEL SAFETY.

HOW TO STOP YOUR UNIT

To stop engine, move ON/OFF switch to the OFF position.

HOW TO START YOUR UNIT

Starting Position

OPERATING POSITION

ALWAYS WEAR:					Eye
ALWAYS WEAR:					Eye

Protection

Long Pants

Heavy Shoes

Cut from your right to your left.

ADVANCING THE CUTTING LINE

Advance line by tapping the bottom of the cut- ting head lightly on the ground while engine is running at full speed. A metal blade attached to the shield will cut the line to the proper length.

TWIST-N-EDGE

SPull the tab toward the engine.

STwist the tube to the edging position; release the tab.

Choke lever

Trigger

Primer Bulb

Muffler

Tab

WARNING: The trimmer head will turn while starting the engine. A hot muffler can cause serious burns.

STARTING A COLD ENGINE (or a warm engine after running out of fuel)

SSet unit on a flat surface.

SMove ON/OFF switch to the ON position. S Slowly press the primer bulb 6 times.

S Move choke lever to FULL CHOKE posi- tion.

S Squeeze the throttle trigger fully and hold through all remaining steps.

S Pull starter rope handle sharply 6 times. S Move choke lever to HALF CHOKE posi-

tion.

S Pull starter rope handle no more than 6 pulls, until engine runs.

S Allow engine to run 10 seconds, then move choke lever to OFF CHOKE position.

STARTING A WARM ENGINE

SMove ON/OFF switch to the ON position. S Move choke lever to OFF CHOKE position. S Pull starter rope handle until engine runs. S If engine does not start in 5 pulls, follow instructions in STARTING A COLD ENGINE.

It is recommended that the engine not be operated for longer than 1 minute at full throttle.

REPLACING THE LINE

SRemove spool by firmly pulling on tap but- ton.

SClean entire surface of hub and spool.

S Replace with a pre-wound spool, or cut a length of 20 feet of 0.080” (2 mm) diameter Weed Eaterr brand line. Never use wire, rope, string, etc., which can break off and become a dangerous missile.

SInsert one end of the line about 1/2 inch (1 cm) into the small hole on the inside of spool.

Small

Hole

Spool

Line in Notch

Hub	Line exit hole

S Wind the line evenly and tightly onto the spool. Wind in the direction of the arrow found on the spool.

SPush the line into the notch, leaving 3 to 5 inches (7 -- 12 cm) unwound.

530086412 specifications

The Weed Eater 530086412 is a versatile and reliable outdoor power tool designed for both residential and commercial users. This weed eater stands out for its cutting-edge features and advanced technology, making it an excellent option for tackling overgrown lawns, gardens, and other green spaces.

One of the primary features of the Weed Eater 530086412 is its powerful engine. The 28cc two-stroke engine delivers impressive torque and cutting power while remaining lightweight and easy to maneuver. This makes it ideal for extended use without causing excessive fatigue. The engine is designed to run efficiently, providing a balance of power and fuel economy that keeps efficiency at the forefront of your yard maintenance.

Another significant characteristic of the Weed Eater 530086412 is its innovative cutting system. It is equipped with a dual-line head that allows for quick and easy line replacements. The auto-feed feature ensures that the cutting line is automatically adjusted to the ideal length during operation, making it hassle-free. Additionally, it supports different line sizes, providing versatility for various cutting tasks.

Ergonomically designed, this weed eater features a comfortable handle and a shoulder strap that enhances user comfort during prolonged use. The lightweight design reduces strain on the operator’s arms and back, allowing for easier maneuverability around tight corners and landscaping obstacles.

Users can appreciate the convenience of the Weed Eater 530086412's easy-start technology. The tool incorporates a simplified starting system that minimizes the pull effort required to start the engine, making it accessible for individuals of all experience levels. This feature is particularly useful for those who may struggle with traditional pull-start systems.

Moreover, the Weed Eater 530086412 offers adjustable handle positions, allowing users to customize the tool's setup according to their height and preferred cutting angle. This flexibility ensures a more comfortable and effective cutting experience, enhancing productivity during yard work.

In conclusion, the Weed Eater 530086412 excels in performance, convenience, and ergonomic design. Its robust engine, auto-feed cutting system, and user-friendly features make it a standout choice for both casual gardeners and landscape professionals. Whether you're maintaining your lawn or tackling tougher weed problems, this model provides the power and flexibility needed to get the job done efficiently.