Sears C944.414460 Replace Spark Plug, Replace Fuel Filter, Chain Sharpening, Chain Replacement

Page 17

Outlet Cover

Exhaust Outlets

Exhaust Outlets must face chain brake (bar side) of chain saw

9.Inspect the muffler gasket and re- place if damaged.

10.Reinstall backplates, muffler gas- ket and muffler using muffler bolts. TIghten until secure.

11.Reinstall bolt cover and locknut.

12.Reinstall the spark plug boot.

13.Reinstall the cylinder cover and 3 screws.

REPLACE SPARK PLUG

The spark plug should be replaced each year to ensure the engine starts easier and runs better. Ignition timing is fixed and nonadjustable.

1.Loosen 3 screws on cylinder cover.

2.Remove the cylinder cover.

3.Pull off the spark plug boot.

4.Remove spark plug from cylinder and discard.

5.Replace with Champion CJ--7Y spark plug and tighten securely with a 3/4 inch socket wrench.

Spark plug gap should be 0.025 inch.

6.Reinstall the spark plug boot.

7.Reinstall the cylinder cover and 3 screws. Tighten screws securely.

Cylinder

Cover

Spark

Plug

Spark

Plug

Spark

Boot

Plug

Boot

REPLACE FUEL FILTER

To replace the fuel filter, drain your unit by running it dry of fuel. Remove fuel cap and its connected retainer from tank. Pull filter from tank and remove from line. Replace and reassemble.

WARNING: Disconnect the spark plug before performing maintenance, service, or adjustments except for car- buretor adjustments.

CHAIN SHARPENING

Chain sharpening requires special tools. You can purchase sharpening tools at Sears or go to a professional chain sharpener.

CHAIN REPLACEMENT

WARNING: Wear protective gloves when handling chain. The chain is sharp and can cut you even when it is not moving.

It is normal for a new chain to stretch during the first 15 minutes of operation. You should recheck your chain tension frequently and adjust the chain tension as required. See CHAIN TENSION sec- tion.

Replace the old chain when it be- comes worn or damaged. Use only the Low-Kickback replacement chain spe- cified in the repair parts list. The cor- rect replacement bar and chain is also specified on a decal located on the chain saw.

See your Sears Service Centre to re- place and sharpen individual cutters on your chain.

TO REPLACE CHAIN:

1.Move ON/STOP switch to the STOP position.

2.Remove chain brake nuts.

3.Remove chain brake.

4.Remove the old chain.

Chain Brake

Clutch Drum

Chain Brake

Nuts

NOTE: An adjusting pin and screw is used to adjust the tension of the chain. It is very important that the pin located on the adjusting screw aligns into the lower hole in the guide bar. Turning the screw will move the adjustment pin up and down the screw.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Gasoline Chain SAW Sears Canada, Inc., Toronto, Ontario M5B 2B8 Limited ONE 1 Year Warranty for Craftsmanr GAS Chain SAWMaintain Your SAW in Good Working Order Plan AheadOperate Your SAW Safely Reduce the Chance Kickback Handle Fuel with CautionGuard Against Kickback Avoid Pinch-Kickback Kickback Safety FeaturesAvoid Pull-In Maintain ControlSpecial Notice Your saw is Chain Brake & CKA AngleKnow Your SAW Carton ContentsAssembly Throttle Trigger ON/STOP Switch Chain BrakeThrottle LOCK--OUT Chain TensionStopping Your Engine ON/STOP Switch Starting PositionStarting a Warm Engine Difficult Starting or starting a flooded engineInertia activating function control Braking function controlOperating Tips Tree Felling TechniquesCutting a Fallen Tree Bucking Felling Large TreesNotch CUT and Felling Tree Important Points Bucking Using a LOG or Support StandBucking Techniques Bucking Without a SupportLimbing Limbing and Pruning Important PointsPruning All the way through the limbGeneral Recommendations Customer ResponsibilitiesCheck for Loose Fasteners and PartsCheck Fuel Mixture Level Check Chain SharpnessCheck Guide BAR Clean AIR Filter Inspect and Clean Unit and DecalsCleaning the Spark Arresting Screen LubricationReplace Spark Plug Chain ReplacementReplace Fuel Filter Chain SharpeningIdle Speed--T Chain AdjustmentCarburetor Adjustment Fuel System Seasonal StorageEngine OtherTroubleshooting Table Cause Remedy Trouble Cause Remedy Troubleshooting TableWhere to GET Warranty SER Pair of Emission Related Control Warranty Parts ListNANCE, Replacement and RE

C944.414460 specifications

The Sears C944.414460 is a notable vessel that stands out in the realm of innovative maritime technology. Its design and performance characteristics are geared toward enhancing both efficiency and user experience. One of the main features of the C944.414460 is its robust hull design, which offers exceptional stability and maneuverability, making it suitable for a variety of nautical applications. The vessel's construction incorporates advanced composite materials that not only reduce weight but also improve durability, ensuring a longer lifespan even in harsh marine conditions.

Equipped with a state-of-the-art propulsion system, the C944.414460 utilizes a hybrid engine that combines traditional fuel technology with electric power, allowing for enhanced fuel efficiency and reduced emissions. This eco-friendly approach aligns with modern environmental standards and appeals to a growing market of environmentally conscious consumers. The result is a vessel that performs exceptionally well while minimizing its ecological footprint.

In terms of onboard technology, the C944.414460 features an intuitive navigation system that integrates GPS, radar, and sonar capabilities to provide real-time data and analytics. This system enhances safety and situational awareness, making it easier for operators to make informed decisions while at sea. Additionally, the inclusion of advanced communication equipment ensures seamless connectivity, allowing for constant monitoring and support from shore-based services.

The interior space of the C944.414460 is designed with comfort and functionality in mind. Thoughtful layout and high-quality finishes contribute to an inviting atmosphere for both crew and passengers. The vessel also boasts generous storage solutions that maximize usability without compromising aesthetics. Advanced climate control systems ensure a pleasant environment, regardless of external weather conditions.

Safety is paramount in the design of the C944.414460, which is equipped with multiple redundancy systems to mitigate potential risks. These safety features include advanced fire suppression systems and emergency backup power supplies, ensuring that the vessel maintains its operational integrity under various circumstances.

In summary, the Sears C944.414460 exemplifies a harmonization of modern design and cutting-edge technology. Its main features, including a hybrid propulsion system, advanced navigation equipment, and safety redundancies, combine to create a vessel that not only meets but exceeds contemporary maritime standards. With a focus on efficiency, comfort, and sustainability, the C944.414460 is a significant innovation in the boating industry.
Top Page Image Contents