Sears C944.414460 Braking function control, Inertia activating function control, Operating Tips

Page 10

Starting could require many pulls de- pending on how badly the unit is flooded. If engine still fails to start, refer to the TROUBLESHOOTING TABLE or contact your Sears Service Centre.

CHAIN BRAKE

WARNING: If the brake band is worn too thin it may break when the chain brake is triggered. With a broken brake band, the chain brake will not stop the chain. The chain brake must be replaced if any part is worn to less than 0.020 inch (0.5 mm) thick. Repairs on a chain brake should be made by your Sears Service Centre. Take your unit to the place of pur- chase or to the nearest Sears Service Centre.

SThis saw is equipped with a chain

brake. The brake is designed to stop the chain if kickback occurs.

SThe inertia--activated chain brake is ac- tivated if the front hand guard is pushed forward, either manually (by hand) or

automatically (by sudden movement).

SIf the brake is already activated, it is dis- engaged by pulling the front hand guard back toward the front handle as far as

possible.

S When cutting with the saw, the chain brake must be disengaged.

Disengaged

Engaged

Braking function control

CAUTION: The chain brake must be checked several times daily. The engine must be running when performing this procedure. This is the only instance when the saw should be placed on the ground with the engine running.

Place the saw on firm ground. Hold the handles with both hands and apply full throttle. Activate the chain brake by turn- ing your left wrist against the hand guard without releasing your grip around the front handle. The chain should stop imme- diately.

Inertia activating function control

WARNING: When performing the following procedure, the engine must be turned off.

Hold the chain saw approximately 14” (35 cm) above a stump or other wood- en surface. Release your grip on the

front handle and use the weight of the saw to let the tip of the guide bar fall forward and contact the stump. When the tip of the bar hits the stump, the brake should activate.

OPERATING TIPS

SCheck chain tension before first use and after 1 minute of operation. See

CHAIN TENSION in the MAINTENANCE

section.

SCut wood only. Do not cut metal, plastics, masonry, non-wood building materials, etc.

SStop the saw if the chain strikes a foreign object. Inspect the saw and

repair parts as necessary.

SKeep the chain out of dirt and sand. Even a small amount of dirt will quickly dull a chain and increase the

possibility of kickback.

SPractice cutting a few small logs us- ing the following steps. This will help you get the “feel” of using your saw before you begin a major sawing op- eration.

S Squeeze the throttle trigger and al- low the engine to reach full speed before cutting.

S Begin cutting with the saw frame against the log.

S Keep the engine at full speed the entire time you are cutting.

S Allow the chain to cut for you. Exert only light downward pressure.

S Release the throttle trigger as soon as the cut is completed, allowing the engine to idle. If you run the saw at full throttle without a cutting load, unnecessary wear can occur.

S To avoid losing control when cut is complete, do not put pressure on saw at end of cut.

SStop engine before setting saw down.

TREE FELLING TECHNIQUES

WARNING: Check for broken or dead branches which can fall while cutting causing serious injury. Do not cut near buildings or electrical wires if you do not know the direction of tree fall, nor cut at night since you will not be able to see well, nor during bad weather such as rain, snow, or strong winds, etc.

SCarefully plan your sawing operation in advance.

SClear the work area. You need a clear area all around the tree so you can have secure footing.

10

Image 10
Contents Gasoline Chain SAW Limited ONE 1 Year Warranty for Craftsmanr GAS Chain SAW Sears Canada, Inc., Toronto, Ontario M5B 2B8Operate Your SAW Safely Plan AheadMaintain Your SAW in Good Working Order Guard Against Kickback Handle Fuel with CautionReduce the Chance Kickback Avoid Pull-In Kickback Safety FeaturesAvoid Pinch-Kickback Maintain ControlChain Brake & CKA Angle Special Notice Your saw isAssembly Carton ContentsKnow Your SAW Throttle LOCK--OUT ON/STOP Switch Chain BrakeThrottle Trigger Chain TensionStarting a Warm Engine ON/STOP Switch Starting PositionStopping Your Engine Difficult Starting or starting a flooded engineOperating Tips Braking function controlInertia activating function control Tree Felling TechniquesNotch CUT and Felling Tree Felling Large TreesCutting a Fallen Tree Bucking Bucking Techniques Bucking Using a LOG or Support StandImportant Points Bucking Without a SupportPruning Limbing and Pruning Important PointsLimbing All the way through the limbCheck for Loose Customer ResponsibilitiesGeneral Recommendations Fasteners and PartsCheck Guide BAR Check Chain SharpnessCheck Fuel Mixture Level Cleaning the Spark Arresting Screen Inspect and Clean Unit and DecalsClean AIR Filter LubricationReplace Fuel Filter Chain ReplacementReplace Spark Plug Chain SharpeningCarburetor Adjustment Chain AdjustmentIdle Speed--T Engine Seasonal StorageFuel System OtherTroubleshooting Table Cause Remedy Troubleshooting Table Trouble Cause RemedyWhere to GET Warranty SER NANCE, Replacement and RE Control Warranty Parts ListPair of Emission Related

C944.414460 specifications

The Sears C944.414460 is a notable vessel that stands out in the realm of innovative maritime technology. Its design and performance characteristics are geared toward enhancing both efficiency and user experience. One of the main features of the C944.414460 is its robust hull design, which offers exceptional stability and maneuverability, making it suitable for a variety of nautical applications. The vessel's construction incorporates advanced composite materials that not only reduce weight but also improve durability, ensuring a longer lifespan even in harsh marine conditions.

Equipped with a state-of-the-art propulsion system, the C944.414460 utilizes a hybrid engine that combines traditional fuel technology with electric power, allowing for enhanced fuel efficiency and reduced emissions. This eco-friendly approach aligns with modern environmental standards and appeals to a growing market of environmentally conscious consumers. The result is a vessel that performs exceptionally well while minimizing its ecological footprint.

In terms of onboard technology, the C944.414460 features an intuitive navigation system that integrates GPS, radar, and sonar capabilities to provide real-time data and analytics. This system enhances safety and situational awareness, making it easier for operators to make informed decisions while at sea. Additionally, the inclusion of advanced communication equipment ensures seamless connectivity, allowing for constant monitoring and support from shore-based services.

The interior space of the C944.414460 is designed with comfort and functionality in mind. Thoughtful layout and high-quality finishes contribute to an inviting atmosphere for both crew and passengers. The vessel also boasts generous storage solutions that maximize usability without compromising aesthetics. Advanced climate control systems ensure a pleasant environment, regardless of external weather conditions.

Safety is paramount in the design of the C944.414460, which is equipped with multiple redundancy systems to mitigate potential risks. These safety features include advanced fire suppression systems and emergency backup power supplies, ensuring that the vessel maintains its operational integrity under various circumstances.

In summary, the Sears C944.414460 exemplifies a harmonization of modern design and cutting-edge technology. Its main features, including a hybrid propulsion system, advanced navigation equipment, and safety redundancies, combine to create a vessel that not only meets but exceeds contemporary maritime standards. With a focus on efficiency, comfort, and sustainability, the C944.414460 is a significant innovation in the boating industry.