To enter each sub menu, press the Pause key | Toshiba B-SX8T

2. SYSTEM MODE

EO13-33002

2.7 IP Address Setting

When “<7>IP ADDRESS” appears, press the [PAUSE] key.

Choose an IP Address menu among “Printer IP Address”, “Socket Port”, “Gateway IP Address”, “Subnet Mask”, or “DHCP”.

[RESTART]

[FEED]

PRINTER IP ADRES

GATEWAY IP ADRES

SUBNET MASK

SOCKET PORT

DHCP

DHCP CLIENT ID

DHCP HOST NAME

To enter each sub menu, press the [PAUSE] key.

2.7.1 Printer IP Address, Gateway IP Address, and Subnet Mask Settings

When “PRINTER IP ADRES” is displayed, press the [PAUSE] key.

PRINTER IP ADRES

Set the IP address using the following procedure.

192.168.010.020

Set the first 3-digit value with the [FEED] or [RESTART] key.

Press the [PAUSE] key to move the cursor to the next 3-digit value.

Set the next values in the same way.

192.168.010.020				192.168.010.020				192.168.010.020

NOTES: 1. Pressing the [FEED] key one time causes a –1 change. Pressing the [RESTART] key one time causes a +1 change.

2.If holding the [FEED] or [RESTART] key for 0.5 seconds or longer in the parameter setting, the key is entered continuously.

After the last 3-digit value is set, press the [PAUSE] key. The display will show “GATEWAY IP ADDRESS”. Set the values for the Gateway IP Address and Subnet Mask, respectively.

2-67

Image 73

Toshiba B-SX8T manual To enter each sub menu, press the Pause key, When Printer IP Adres is displayed, press the Pause key

Contents

SX6T/SX8T Series Table of Contents Test Print Printer Parameter Fine Adjustment Program Down Load On Line ModeRfid Analyze Tool Key Operation Flow Introduction Operation Panel → Section This is the start of the IP Address Setting menu. → Section This is the Rfid Module Setting menu This is the start of the Basic Setting menu8BASIC Pause 10RFID Pause „ Outline of Self-diagnostic Test Self-diagnostic Test„ How to Enter Self-diagnostic Test Mode PRT Type Transfr Dispensing Mode Selection Printing Mode SelectionPRT Type no Tran PRT Type Direct Maintenance Checking & Print Maintenance Counter/Parameter Settings Print Out Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Font Descriptions of the Parameters ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic Print Sample Self-Diagnostic Test and Result Print OutAfter printing is completed, the display returns to 1DIAG Alphanumeric Font ROM Check DescriptionsKanji ROM Check Eeprom Check Sdram Capacity Sensor/Switch Print status description Sensor/Thermistor Sensor 2 Check =300 GNDhms Manual Threshold Check Rfid module check Results of a Rfid module check is printed Internal Serial Interface CheckDIN Press the Pause key to return to 1DIAG Print Head Element Check Outline of Parameter Setting Parameter Setting Character Code Selection How to Enter Parameter Setting ModeUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Baud Rate Selection Character Zero SelectionAfter selecting a character zero, press the Pause key After selecting a baud rate, press the Pause key Stop Bit Length Selection Data Length SelectionAfter selecting a data length, press the Pause key After selecting a stop bit, press the Pause key Flow Control Code Selection Parity SelectionAfter selecting the parity, press the Pause key Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key Ribbon Save Function Selection Head Up Cut Selection 2PARAMETER SET Code Auto Control Code SelectionCode Auto Code ESC,LF,NUL Code Manual 2PARAMETER SET Control CODE1 1B Strip Wait Status Selection Ribbon Type SelectionAfter selecting a ribbon type, press the Pause key After selecting the Strip Wait Status, press the Pause key Kanji Code Selection Feed Key Function SelectionEuro Code Selection Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key Media Sensor Selection Web Printer Function SelectionAfter selecting the media sensor type, press the Pause key Expansion I/O Interface Type Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Label End/Ribbon End Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key TYPE1 Pre-Strip Selection Maxi Code Specification SelectionReverse Feed Speed Selection Press the Pause key to skip Stabilizer Function Selection Strip Motor Torque Selection2PARAMETER SET Peel OFF TRQ R0 2PARAMETER SET Stabilizer on Outline of Printer Parameter Fine Adjustment Printer Parameter Fine Adjustment 3ADJUST SET How to Enter Printer Parameter Fine Adjustment Mode After completing the fine adjustment, press the Pause key Print Start Position Fine AdjustmentPrint Start Position Fine Adjustment Example Example of Cut Position Fine Adjustment 2 Cut/Strip Position Fine AdjustmentWhen setting +0.0 mm Prevention by fine adjustment of the cut position Example of Strip Position Fine Adjustment Operation example Issue count 3, Cut interval Example of Reverse Feed Amount Fine Adjustment Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Darker Standard Lighter Maximum fine adjustment value High Standard Low Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor 3ADJUST SET THRESHOLDR1.0V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDT1.4V Outline of Test Print Test Print Media Ribbon Save Area 8 mm How to Enter Test Print Mode4TEST Print Select an issue count from a range of 1 to Issue Count SettingPrint Speed Setting Specifying the Print Condition for the Test Print Issue Mode Selection Printing Mode SelectionSensor Type Selection Paper Feed Selection Media Length Setting4TEST Print Paper Feed Test Print Pattern Selection Slant Line 1 dot Print Sample of Slant Line 3 dots Slant Line 3 dots Barcode CharactersPrint Sample of Characters Print Sample of Barcodes Factory Test Non-PrintingPrint Sample of Non-print Print Sample of Factory Test Pause key Auto PrintPrints bar codes on 5 pieces of media Prints characters on 5 pieces of media Outline of the Sensor Adjustment Sensor Adjustment How to Enter the Sensor Adjustment Mode Black Mark Sensor AdjustmentThermistor Status Display 5SENSOR ADJ Ribbon End Sensor Adjustment Ribbon Level Feed Gap Sensor AdjustmentPress the Pause key to return to 5SENSOR ADJ. display 5SENSOR ADJ. Trans RAM Clear How to Enter RAM Clear ModeOutline of RAM Clear 6RAM Clear RAM Clear Menu Selection Maintenance Counter ClearNo RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Solenoid drive time for head up Parameter ClearMode Initial values after clearing the parameters Parameter Clear 170.6 mm Outline of the IP Address Setting IP Address SettingHow to Enter IP Address Setting Mode 7IP Address Set the IP address using the following procedure When Printer IP Adres is displayed, press the Pause keyTo enter each sub menu, press the Pause key Printer IP Adres Dhcp and Dhcp Client ID Setting Socket Port SettingTo set a socket port number, follow the procedure below Mode Ascii Dhcp Host Name Dhcp Host Name SettingMode Ascii Ascii code and Hex. code correspondence table How to Enter Basic Setting Mode Basic SettingOutline of Basic Setting 8BASIC Basic Trace Selection Mode Basic Specification Selection ModeBasic File Browser Basic Expansion Mode Execution of Basic Program Outline of the Rfid Module Setting Rfid Module Setting Read Test Procedure How to Enter Rfid Module Setting ModeRfid Read Test Press the Restart key or Feed key until 10RFID appears Module None Rfid Module Type SelectionModule None Module U2 Rfid Tag Type Selection Rfid Error Tag Detection Issue Retry Maximum Number of Rfid Issue Retries Cycle CNT Maximum Number of Rfid Read Retries After selecting the time-out, press the Pause key Rfid Read Retry Time-outCycle TIM Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Adjustment in negative − direction Rfid Adjustment for RetryAdjustment in positive + direction After selecting the adjustment value, press the Pause key When AGC Threshold is displayed, press the Pause key Rfid Wireless Power Level SettingPower Level Rfid AGC Threshold Value Rfid Module Q Value SettingQvalue When WT AGC is displayed, press the Pause key AGC Threshold for Data Write SettingWT AGC WT MIN AGC AGC Threshold Lower Limit for Retry Setting On Line Mode „ LCD message and LED indication Symbols in the message Rfid Write Error System Error „ Outline of Automatic Threshold Setting Automatic Threshold Setting„ How to Perform an Automatic Threshold Setting „ How to Perform a Reset Operation Reset Operation1RESET „ How to Perform a Dump Operation Dump Mode Print Conditions Data in the receive buffer is printed as followsReceive buffer size Required label length „ How to Perform Basic Expansion Basic Expansion Mode5EXPAND Mode „ How to Choose an Automatic Calibration Setting Automatic Calibration Setting6AUTO Calib 6AUTO Calib OFF On Line Mode „ How to Enable/Disable the LAN LAN Enable/Disable SettingOn Snmp on „ How to perform the Real Time Clock Setting Real Time Clock RTC Setting8RTC SET 8RTC SET Date M 8RTC SET Time M 8RTC SET Time H8RTC SET Time S 8RTC SET LOW BATT. Check On Line Mode Download Program Installation Outline of FeaturesSystem Requirements Setup Disk SetupInstallation Procedure Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load System Requirement Rfid Analyze Tool Setup Disk Installation Setup Disk consists of one CD-ROM Set upSX/SA Rfid Analyze Tool V1.5 Main Menu Application FunctionsU2 B-SX704-RFID-U2-EU/AU/US/CN-R SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Example Help MenuDisplays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R Tag Data EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box