SX704-RFID-U2-EU/AU/US/CN-R U2 | Toshiba B-SX8T, B-SX6T guide

5.RFID ANALYZE TOOL

EO13-33002

(Revision Date: Mar. 26, 2009)

5.4 Operatin Procedure

4.Set the following parameters.

RFID module type to be analyzed (RFID Module Select)

Choose the RFID module to be used for the RFID Module Select parameter.

B-9704-RFID-U1-US/EU:“U1”

B-9704-RFID-H1-QM:“H1”

B-SX704-RFID-U2-EU/AU/US/CN-R: “U2”

B-SX708-RFID-U2-EU/CN-R: “U2”

RFID Module Select

5- 16

Image 129

Toshiba B-SX8T, B-SX6T manual SX704-RFID-U2-EU/AU/US/CN-R U2

Contents

SX6T/SX8T Series Table of Contents Test Print Printer Parameter Fine Adjustment On Line Mode Program Down LoadRfid Analyze Tool Key Operation Flow Introduction Operation Panel → Section This is the start of the IP Address Setting menu. → Section This is the Rfid Module Setting menu This is the start of the Basic Setting menu8BASIC Pause 10RFID Pause „ Outline of Self-diagnostic Test Self-diagnostic Test„ How to Enter Self-diagnostic Test Mode PRT Type Transfr Dispensing Mode Selection Printing Mode SelectionPRT Type no Tran PRT Type Direct Maintenance Checking & Print Maintenance Counter/Parameter Settings Print Out Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Font Descriptions of the Parameters ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic Self-Diagnostic Test and Result Print Out Print SampleAfter printing is completed, the display returns to 1DIAG Alphanumeric Font ROM Check DescriptionsKanji ROM Check Eeprom Check Sdram Capacity Sensor/Switch Print status description Sensor/Thermistor Sensor 2 Check =300 GNDhms Manual Threshold Check Internal Serial Interface Check Rfid module check Results of a Rfid module check is printedDIN Press the Pause key to return to 1DIAG Print Head Element Check Outline of Parameter Setting Parameter Setting Character Code Selection How to Enter Parameter Setting ModeUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Baud Rate Selection Character Zero SelectionAfter selecting a character zero, press the Pause key After selecting a baud rate, press the Pause key Stop Bit Length Selection Data Length SelectionAfter selecting a data length, press the Pause key After selecting a stop bit, press the Pause key Parity Selection Flow Control Code SelectionAfter selecting the parity, press the Pause key LCD Language Selection Auto Forward Wait SelectionAfter selecting a language, press the Pause key Ribbon Save Function Selection Head Up Cut Selection 2PARAMETER SET Code Auto Control Code SelectionCode Auto Code ESC,LF,NUL Code Manual 2PARAMETER SET Control CODE1 1B Strip Wait Status Selection Ribbon Type SelectionAfter selecting a ribbon type, press the Pause key After selecting the Strip Wait Status, press the Pause key Feed Key Function Selection Kanji Code SelectionEuro Code Selection Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key Web Printer Function Selection Media Sensor SelectionAfter selecting the media sensor type, press the Pause key Input Prime Selection Expansion I/O Interface Type SelectionAfter selecting the Input Prime, press the Pause key Plug & Play Selection Label End/Ribbon End SelectionAfter selecting a Plug & Play, press the Pause key TYPE1 Pre-Strip Selection Maxi Code Specification SelectionReverse Feed Speed Selection Press the Pause key to skip Stabilizer Function Selection Strip Motor Torque Selection2PARAMETER SET Peel OFF TRQ R0 2PARAMETER SET Stabilizer on Outline of Printer Parameter Fine Adjustment Printer Parameter Fine Adjustment 3ADJUST SET How to Enter Printer Parameter Fine Adjustment Mode Print Start Position Fine Adjustment After completing the fine adjustment, press the Pause keyPrint Start Position Fine Adjustment Example 2 Cut/Strip Position Fine Adjustment Example of Cut Position Fine AdjustmentWhen setting +0.0 mm Prevention by fine adjustment of the cut position Example of Strip Position Fine Adjustment Operation example Issue count 3, Cut interval Example of Reverse Feed Amount Fine Adjustment Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Darker Standard Lighter Maximum fine adjustment value High Standard Low Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor 3ADJUST SET THRESHOLDR1.0V3ADJUST SET THRESHOLDT1.4V Outline of Test Print Test Print How to Enter Test Print Mode Media Ribbon Save Area 8 mm4TEST Print Select an issue count from a range of 1 to Issue Count SettingPrint Speed Setting Specifying the Print Condition for the Test Print Printing Mode Selection Issue Mode SelectionSensor Type Selection Media Length Setting Paper Feed Selection4TEST Print Paper Feed Test Print Pattern Selection Slant Line 1 dot Print Sample of Slant Line 3 dots Slant Line 3 dots Barcode CharactersPrint Sample of Characters Print Sample of Barcodes Factory Test Non-PrintingPrint Sample of Non-print Print Sample of Factory Test Pause key Auto PrintPrints bar codes on 5 pieces of media Prints characters on 5 pieces of media Outline of the Sensor Adjustment Sensor Adjustment How to Enter the Sensor Adjustment Mode Black Mark Sensor AdjustmentThermistor Status Display 5SENSOR ADJ Ribbon End Sensor Adjustment Ribbon Level Feed Gap Sensor AdjustmentPress the Pause key to return to 5SENSOR ADJ. display 5SENSOR ADJ. Trans RAM Clear How to Enter RAM Clear ModeOutline of RAM Clear 6RAM Clear RAM Clear Menu Selection Maintenance Counter ClearNo RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Parameter Clear Solenoid drive time for head upMode Initial values after clearing the parameters Parameter Clear 170.6 mm Outline of the IP Address Setting IP Address SettingHow to Enter IP Address Setting Mode 7IP Address Set the IP address using the following procedure When Printer IP Adres is displayed, press the Pause keyTo enter each sub menu, press the Pause key Printer IP Adres Socket Port Setting Dhcp and Dhcp Client ID SettingTo set a socket port number, follow the procedure below Mode Ascii Dhcp Host Name Dhcp Host Name SettingMode Ascii Ascii code and Hex. code correspondence table How to Enter Basic Setting Mode Basic SettingOutline of Basic Setting 8BASIC Basic Specification Selection Mode Basic Trace Selection ModeBasic File Browser Basic Expansion Mode Execution of Basic Program Outline of the Rfid Module Setting Rfid Module Setting Read Test Procedure How to Enter Rfid Module Setting ModeRfid Read Test Press the Restart key or Feed key until 10RFID appears Rfid Module Type Selection Module NoneModule None Module U2 Rfid Tag Type Selection Rfid Error Tag Detection Issue Retry Maximum Number of Rfid Issue Retries Cycle CNT Maximum Number of Rfid Read Retries Rfid Read Retry Time-out After selecting the time-out, press the Pause keyCycle TIM Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Adjustment in negative − direction Rfid Adjustment for RetryAdjustment in positive + direction After selecting the adjustment value, press the Pause key When AGC Threshold is displayed, press the Pause key Rfid Wireless Power Level SettingPower Level Rfid AGC Threshold Rfid Module Q Value Setting ValueQvalue AGC Threshold for Data Write Setting When WT AGC is displayed, press the Pause keyWT AGC WT MIN AGC AGC Threshold Lower Limit for Retry Setting On Line Mode „ LCD message and LED indication Symbols in the message Rfid Write Error System Error Automatic Threshold Setting „ Outline of Automatic Threshold Setting„ How to Perform an Automatic Threshold Setting Reset Operation „ How to Perform a Reset Operation1RESET „ How to Perform a Dump Operation Dump Mode Print Conditions Data in the receive buffer is printed as followsReceive buffer size Required label length Basic Expansion Mode „ How to Perform Basic Expansion5EXPAND Mode „ How to Choose an Automatic Calibration Setting Automatic Calibration Setting6AUTO Calib 6AUTO Calib OFF On Line Mode LAN Enable/Disable Setting „ How to Enable/Disable the LANOn Snmp on „ How to perform the Real Time Clock Setting Real Time Clock RTC Setting8RTC SET 8RTC SET Date M 8RTC SET Time M 8RTC SET Time H8RTC SET Time S 8RTC SET LOW BATT. Check On Line Mode Outline of Features Download Program InstallationSystem Requirements Setup Disk SetupInstallation Procedure Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load System Requirement Rfid Analyze Tool Setup Disk Installation Setup Disk consists of one CD-ROM Set upSX/SA Rfid Analyze Tool V1.5 Main Menu Application FunctionsU2 B-SX704-RFID-U2-EU/AU/US/CN-R SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Help Menu ExampleDisplays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R Tag Data EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box