Help Menu, Example | Toshiba B-SX8T, B-SX6T manual

5.RFID ANALYZE TOOL

EO13-33002

(Revision Date: Jul. 24, 2008)

5.3 Application Functions

5.3.4 Help Menu

Displays Printer Version and RFID Module Version.

Printer Version

RFID Module Version

Example

Printer Version

RFID Module Version

NOTE: Printer version and module version are indicated next to the date and time of Log file. Example) CSV file information

Date&Time = 07/10/16 09:47:24: Printer Information = B-SX4T Z4.4C 27SEP2007 Module Information = U2 JPN #00PV971

5- 12

Image 125

Toshiba B-SX8T, B-SX6T manual Help Menu, Example, Displays Printer Version and Rfid Module Version

Contents

SX6T/SX8T Series Table of Contents Test Print Printer Parameter Fine Adjustment Rfid Analyze Tool On Line ModeProgram Down Load Key Operation Flow Introduction Operation Panel → Section This is the start of the IP Address Setting menu. → Section This is the Rfid Module Setting menu This is the start of the Basic Setting menu8BASIC Pause 10RFID Pause „ Outline of Self-diagnostic Test Self-diagnostic Test„ How to Enter Self-diagnostic Test Mode PRT Type Transfr Dispensing Mode Selection Printing Mode SelectionPRT Type no Tran PRT Type Direct Maintenance Checking & Print Maintenance Counter/Parameter Settings Print Out Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Font Descriptions of the Parameters ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic After printing is completed, the display returns to 1DIAG Self-Diagnostic Test and Result Print OutPrint Sample Alphanumeric Font ROM Check DescriptionsKanji ROM Check Eeprom Check Sdram Capacity Sensor/Switch Print status description Sensor/Thermistor Sensor 2 Check =300 GNDhms Manual Threshold Check DIN Internal Serial Interface CheckRfid module check Results of a Rfid module check is printed Press the Pause key to return to 1DIAG Print Head Element Check Outline of Parameter Setting Parameter Setting Character Code Selection How to Enter Parameter Setting ModeUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Baud Rate Selection Character Zero SelectionAfter selecting a character zero, press the Pause key After selecting a baud rate, press the Pause key Stop Bit Length Selection Data Length SelectionAfter selecting a data length, press the Pause key After selecting a stop bit, press the Pause key After selecting the parity, press the Pause key Parity SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection Ribbon Save Function Selection Head Up Cut Selection 2PARAMETER SET Code Auto Control Code SelectionCode Auto Code ESC,LF,NUL Code Manual 2PARAMETER SET Control CODE1 1B Strip Wait Status Selection Ribbon Type SelectionAfter selecting a ribbon type, press the Pause key After selecting the Strip Wait Status, press the Pause key Euro Code Selection Feed Key Function SelectionKanji Code Selection Centronics Interface ACK/BUSY Timing Selection Auto Print Head Check SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key After selecting the media sensor type, press the Pause key Web Printer Function SelectionMedia Sensor Selection After selecting the Input Prime, press the Pause key Input Prime SelectionExpansion I/O Interface Type Selection After selecting a Plug & Play, press the Pause key Plug & Play SelectionLabel End/Ribbon End Selection TYPE1 Pre-Strip Selection Maxi Code Specification SelectionReverse Feed Speed Selection Press the Pause key to skip Stabilizer Function Selection Strip Motor Torque Selection2PARAMETER SET Peel OFF TRQ R0 2PARAMETER SET Stabilizer on Outline of Printer Parameter Fine Adjustment Printer Parameter Fine Adjustment 3ADJUST SET How to Enter Printer Parameter Fine Adjustment Mode Print Start Position Fine Adjustment Example Print Start Position Fine AdjustmentAfter completing the fine adjustment, press the Pause key When setting +0.0 mm 2 Cut/Strip Position Fine AdjustmentExample of Cut Position Fine Adjustment Prevention by fine adjustment of the cut position Example of Strip Position Fine Adjustment Operation example Issue count 3, Cut interval Example of Reverse Feed Amount Fine Adjustment Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Darker Standard Lighter Maximum fine adjustment value High Standard Low Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor 3ADJUST SET THRESHOLDT1.4V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDR1.0V Outline of Test Print Test Print 4TEST Print How to Enter Test Print ModeMedia Ribbon Save Area 8 mm Select an issue count from a range of 1 to Issue Count SettingPrint Speed Setting Specifying the Print Condition for the Test Print Sensor Type Selection Printing Mode SelectionIssue Mode Selection 4TEST Print Paper Feed Media Length SettingPaper Feed Selection Test Print Pattern Selection Slant Line 1 dot Print Sample of Slant Line 3 dots Slant Line 3 dots Barcode CharactersPrint Sample of Characters Print Sample of Barcodes Factory Test Non-PrintingPrint Sample of Non-print Print Sample of Factory Test Pause key Auto PrintPrints bar codes on 5 pieces of media Prints characters on 5 pieces of media Outline of the Sensor Adjustment Sensor Adjustment How to Enter the Sensor Adjustment Mode Black Mark Sensor AdjustmentThermistor Status Display 5SENSOR ADJ Ribbon End Sensor Adjustment Ribbon Level Feed Gap Sensor AdjustmentPress the Pause key to return to 5SENSOR ADJ. display 5SENSOR ADJ. Trans RAM Clear How to Enter RAM Clear ModeOutline of RAM Clear 6RAM Clear RAM Clear Menu Selection Maintenance Counter ClearNo RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Mode Parameter ClearSolenoid drive time for head up Initial values after clearing the parameters Parameter Clear 170.6 mm Outline of the IP Address Setting IP Address SettingHow to Enter IP Address Setting Mode 7IP Address Set the IP address using the following procedure When Printer IP Adres is displayed, press the Pause keyTo enter each sub menu, press the Pause key Printer IP Adres To set a socket port number, follow the procedure below Socket Port SettingDhcp and Dhcp Client ID Setting Mode Ascii Dhcp Host Name Dhcp Host Name SettingMode Ascii Ascii code and Hex. code correspondence table How to Enter Basic Setting Mode Basic SettingOutline of Basic Setting 8BASIC Basic File Browser Basic Specification Selection ModeBasic Trace Selection Mode Basic Expansion Mode Execution of Basic Program Outline of the Rfid Module Setting Rfid Module Setting Read Test Procedure How to Enter Rfid Module Setting ModeRfid Read Test Press the Restart key or Feed key until 10RFID appears Module None Module U2 Rfid Module Type SelectionModule None Rfid Tag Type Selection Rfid Error Tag Detection Issue Retry Maximum Number of Rfid Issue Retries Cycle CNT Maximum Number of Rfid Read Retries Cycle TIM Rfid Read Retry Time-outAfter selecting the time-out, press the Pause key Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Adjustment in negative − direction Rfid Adjustment for RetryAdjustment in positive + direction After selecting the adjustment value, press the Pause key When AGC Threshold is displayed, press the Pause key Rfid Wireless Power Level SettingPower Level Rfid AGC Threshold Qvalue Rfid Module Q Value SettingValue WT AGC AGC Threshold for Data Write SettingWhen WT AGC is displayed, press the Pause key WT MIN AGC AGC Threshold Lower Limit for Retry Setting On Line Mode „ LCD message and LED indication Symbols in the message Rfid Write Error System Error „ How to Perform an Automatic Threshold Setting Automatic Threshold Setting„ Outline of Automatic Threshold Setting 1RESET Reset Operation„ How to Perform a Reset Operation „ How to Perform a Dump Operation Dump Mode Print Conditions Data in the receive buffer is printed as followsReceive buffer size Required label length 5EXPAND Mode Basic Expansion Mode„ How to Perform Basic Expansion „ How to Choose an Automatic Calibration Setting Automatic Calibration Setting6AUTO Calib 6AUTO Calib OFF On Line Mode On Snmp on LAN Enable/Disable Setting„ How to Enable/Disable the LAN „ How to perform the Real Time Clock Setting Real Time Clock RTC Setting8RTC SET 8RTC SET Date M 8RTC SET Time M 8RTC SET Time H8RTC SET Time S 8RTC SET LOW BATT. Check On Line Mode System Requirements Outline of FeaturesDownload Program Installation Setup Disk SetupInstallation Procedure Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load System Requirement Rfid Analyze Tool Setup Disk Installation Setup Disk consists of one CD-ROM Set upSX/SA Rfid Analyze Tool V1.5 Main Menu Application FunctionsU2 B-SX704-RFID-U2-EU/AU/US/CN-R SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Displays Printer Version and Rfid Module Version Help MenuExample Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R Tag Data EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box