LAN Enable/Disable Setting, On Snmp on | Toshiba B-SX8T, B-SX6T

3. ON LINE MODE

EO13-33002

3.6 LAN Enable/Disable Setting

3.6 LAN Enable/Disable Setting

Whether to enable the LAN or not and whether to enable Simple Network Management Protocol (SNMP) or not are chosen by this menu.

How to Enable/Disable the LAN

ON LINE

B-SX8T Vx.x

[PAUSE]

PAUSE 52

B-SX8T Vx.x

Press and hold the [RESTART] key for 3 seconds or longer.

<1>RESET

Press the [RESTART] key.

<7>LAN

[PAUSE]

<7>LAN

ON SNMP ON

[FEED] or [RESTART]

[PAUSE]

Press the [PAUSE] key to stop printing.

The number of remaining print count

NOTE: When the [PAUSE] key is pressed during printing, the number of remaining print count is displayed.

Press the [PAUSE] key to enter the LAN Enable/disable setting menu.

Choose one of the following using the [FEED] or [RESTART] key.

•ON SNMP ON: LAN and SNMP are enabled.

• ON	SNMP OFF: LAN is enabled, but SNMP is disabled.
• OFF:	LAN is disabled.

<7>LAN

3-11

Image 103

Toshiba B-SX8T, B-SX6T manual LAN Enable/Disable Setting, „ How to Enable/Disable the LAN, On Snmp on

Contents

SX6T/SX8T Series Table of Contents Test Print Printer Parameter Fine Adjustment Program Down Load On Line ModeRfid Analyze Tool Key Operation Flow Introduction Operation Panel → Section This is the start of the IP Address Setting menu. → Section 10RFID Pause This is the start of the Basic Setting menuThis is the Rfid Module Setting menu 8BASIC Pause PRT Type Transfr Self-diagnostic Test„ Outline of Self-diagnostic Test „ How to Enter Self-diagnostic Test Mode PRT Type Direct Printing Mode SelectionDispensing Mode Selection PRT Type no Tran Maintenance Checking & Print Maintenance Counter/Parameter Settings Print Out Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Font Descriptions of the Parameters ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic Print Sample Self-Diagnostic Test and Result Print OutAfter printing is completed, the display returns to 1DIAG Eeprom Check DescriptionsAlphanumeric Font ROM Check Kanji ROM Check Sdram Capacity Sensor/Switch Print status description Sensor/Thermistor Sensor 2 Check =300 GNDhms Manual Threshold Check Rfid module check Results of a Rfid module check is printed Internal Serial Interface CheckDIN Press the Pause key to return to 1DIAG Print Head Element Check Outline of Parameter Setting Parameter Setting After selecting a character code, press the Pause key How to Enter Parameter Setting ModeCharacter Code Selection Use the Feed or Restart key to select a desired option After selecting a baud rate, press the Pause key Character Zero SelectionBaud Rate Selection After selecting a character zero, press the Pause key After selecting a stop bit, press the Pause key Data Length SelectionStop Bit Length Selection After selecting a data length, press the Pause key Flow Control Code Selection Parity SelectionAfter selecting the parity, press the Pause key Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key Ribbon Save Function Selection Head Up Cut Selection 2PARAMETER SET Control CODE1 1B Control Code Selection2PARAMETER SET Code Auto Code Auto Code ESC,LF,NUL Code Manual After selecting the Strip Wait Status, press the Pause key Ribbon Type SelectionStrip Wait Status Selection After selecting a ribbon type, press the Pause key Kanji Code Selection Feed Key Function SelectionEuro Code Selection After selecting an ACK/BUSY timing, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting auto print head check, press the Pause key Media Sensor Selection Web Printer Function SelectionAfter selecting the media sensor type, press the Pause key Expansion I/O Interface Type Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Label End/Ribbon End Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key TYPE1 Press the Pause key to skip Maxi Code Specification SelectionPre-Strip Selection Reverse Feed Speed Selection 2PARAMETER SET Stabilizer on Strip Motor Torque SelectionStabilizer Function Selection 2PARAMETER SET Peel OFF TRQ R0 Outline of Printer Parameter Fine Adjustment Printer Parameter Fine Adjustment 3ADJUST SET How to Enter Printer Parameter Fine Adjustment Mode After completing the fine adjustment, press the Pause key Print Start Position Fine AdjustmentPrint Start Position Fine Adjustment Example Example of Cut Position Fine Adjustment 2 Cut/Strip Position Fine AdjustmentWhen setting +0.0 mm Prevention by fine adjustment of the cut position Example of Strip Position Fine Adjustment Operation example Issue count 3, Cut interval Example of Reverse Feed Amount Fine Adjustment Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Darker Standard Lighter Maximum fine adjustment value High Standard Low Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor 3ADJUST SET THRESHOLDR1.0V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDT1.4V Outline of Test Print Test Print Media Ribbon Save Area 8 mm How to Enter Test Print Mode4TEST Print Specifying the Print Condition for the Test Print Issue Count SettingSelect an issue count from a range of 1 to Print Speed Setting Issue Mode Selection Printing Mode SelectionSensor Type Selection Paper Feed Selection Media Length Setting4TEST Print Paper Feed Test Print Pattern Selection Slant Line 1 dot Print Sample of Slant Line 3 dots Slant Line 3 dots Print Sample of Barcodes CharactersBarcode Print Sample of Characters Print Sample of Factory Test Non-PrintingFactory Test Print Sample of Non-print Prints characters on 5 pieces of media Auto PrintPause key Prints bar codes on 5 pieces of media Outline of the Sensor Adjustment Sensor Adjustment 5SENSOR ADJ Black Mark Sensor AdjustmentHow to Enter the Sensor Adjustment Mode Thermistor Status Display 5SENSOR ADJ. Trans Feed Gap Sensor AdjustmentRibbon End Sensor Adjustment Ribbon Level Press the Pause key to return to 5SENSOR ADJ. display 6RAM Clear How to Enter RAM Clear ModeRAM Clear Outline of RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Maintenance Counter ClearRAM Clear Menu Selection No RAM Clear Solenoid drive time for head up Parameter ClearMode Initial values after clearing the parameters Parameter Clear 170.6 mm 7IP Address IP Address SettingOutline of the IP Address Setting How to Enter IP Address Setting Mode Printer IP Adres When Printer IP Adres is displayed, press the Pause keySet the IP address using the following procedure To enter each sub menu, press the Pause key Dhcp and Dhcp Client ID Setting Socket Port SettingTo set a socket port number, follow the procedure below Ascii code and Hex. code correspondence table Dhcp Host Name SettingMode Ascii Dhcp Host Name Mode Ascii 8BASIC Basic SettingHow to Enter Basic Setting Mode Outline of Basic Setting Basic Trace Selection Mode Basic Specification Selection ModeBasic File Browser Basic Expansion Mode Execution of Basic Program Outline of the Rfid Module Setting Rfid Module Setting Press the Restart key or Feed key until 10RFID appears How to Enter Rfid Module Setting ModeRead Test Procedure Rfid Read Test Module None Rfid Module Type SelectionModule None Module U2 Rfid Tag Type Selection Rfid Error Tag Detection Issue Retry Maximum Number of Rfid Issue Retries Cycle CNT Maximum Number of Rfid Read Retries After selecting the time-out, press the Pause key Rfid Read Retry Time-outCycle TIM Maximum Number of Rfid Write Retries Rfid Write Retry Time-out After selecting the adjustment value, press the Pause key Rfid Adjustment for RetryAdjustment in negative − direction Adjustment in positive + direction Rfid AGC Threshold Rfid Wireless Power Level SettingWhen AGC Threshold is displayed, press the Pause key Power Level Value Rfid Module Q Value SettingQvalue When WT AGC is displayed, press the Pause key AGC Threshold for Data Write SettingWT AGC WT MIN AGC AGC Threshold Lower Limit for Retry Setting On Line Mode „ LCD message and LED indication Symbols in the message Rfid Write Error System Error „ Outline of Automatic Threshold Setting Automatic Threshold Setting„ How to Perform an Automatic Threshold Setting „ How to Perform a Reset Operation Reset Operation1RESET „ How to Perform a Dump Operation Dump Mode Required label length Data in the receive buffer is printed as followsPrint Conditions Receive buffer size „ How to Perform Basic Expansion Basic Expansion Mode5EXPAND Mode 6AUTO Calib OFF Automatic Calibration Setting„ How to Choose an Automatic Calibration Setting 6AUTO Calib On Line Mode „ How to Enable/Disable the LAN LAN Enable/Disable SettingOn Snmp on 8RTC SET Date M Real Time Clock RTC Setting„ How to perform the Real Time Clock Setting 8RTC SET 8RTC SET LOW BATT. Check 8RTC SET Time H8RTC SET Time M 8RTC SET Time S On Line Mode Download Program Installation Outline of FeaturesSystem Requirements Before starting the download procedure SetupSetup Disk Installation Procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load System Requirement Rfid Analyze Tool V1.5 Set upSetup Disk Installation Setup Disk consists of one CD-ROM SX/SA Rfid Analyze Tool SX708-RFID-U2-EU/CN-R Application FunctionsMain Menu U2 B-SX704-RFID-U2-EU/AU/US/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the printer model Select the test mode This menu is not available Example Help MenuDisplays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R Tag Data EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box