EO13-33002 | Toshiba B-SX6T, B-SX8T specs

5.RFID ANALYZE TOOL	EO13-33002
	(Revision Date: Jul. 24, 2008)
	5.3 Application Functions

(2)Log Save As

Saves text data in the “Results” box of the RFID Analyze Tool screen into a text file.

(3)Text Capture

Saves the test result into a CSV file.

Selecting “Text Capture” then “Open” shows “Capture” in the area indicated by “2)” in the figure below. When a write/read test is executed with “Capture” shown, the test result is automatically saved in a CSV file specified.

1)

2)

1)After “Text Capture” is selected, the menu adds “Close” under “Open”. Selecting “Close” exits from this function.

2)When “Text Capture” is selected, ”Capture” is shown.

(4)ParaSave (Parameter Save)

Saves the current test information to facilitate a next test. The saved parameters are invoked at a program boot. Information to be saved are feed amount, number of tries, RFID module type, tag type, communication settings between PC and printer, label size command, Feed command, Sheet count, printer type, and test mode.

5- 5

Image 118

Toshiba B-SX6T, B-SX8T manual EO13-33002

Contents

SX6T/SX8T Series Table of Contents Printer Parameter Fine Adjustment Test Print Program Down Load On Line ModeRfid Analyze Tool Introduction Key Operation Flow Operation Panel This is the start of the IP Address Setting menu. → Section → Section 8BASIC Pause This is the start of the Basic Setting menuThis is the Rfid Module Setting menu 10RFID Pause „ How to Enter Self-diagnostic Test Mode Self-diagnostic Test„ Outline of Self-diagnostic Test PRT Type Transfr PRT Type no Tran Printing Mode SelectionDispensing Mode Selection PRT Type Direct Maintenance Counter/Parameter Settings Print Out Maintenance Checking & Print Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Descriptions of the Parameters Font ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic Print Sample Self-Diagnostic Test and Result Print OutAfter printing is completed, the display returns to 1DIAG Kanji ROM Check DescriptionsAlphanumeric Font ROM Check Eeprom Check Sensor/Switch Print status description Sdram Capacity Sensor 2 Check Sensor/Thermistor Manual Threshold Check =300 GNDhms Rfid module check Results of a Rfid module check is printed Internal Serial Interface CheckDIN Print Head Element Check Press the Pause key to return to 1DIAG Parameter Setting Outline of Parameter Setting Use the Feed or Restart key to select a desired option How to Enter Parameter Setting ModeCharacter Code Selection After selecting a character code, press the Pause key After selecting a character zero, press the Pause key Character Zero SelectionBaud Rate Selection After selecting a baud rate, press the Pause key After selecting a data length, press the Pause key Data Length SelectionStop Bit Length Selection After selecting a stop bit, press the Pause key Flow Control Code Selection Parity SelectionAfter selecting the parity, press the Pause key Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key Head Up Cut Selection Ribbon Save Function Selection Code Auto Code ESC,LF,NUL Code Manual Control Code Selection2PARAMETER SET Code Auto 2PARAMETER SET Control CODE1 1B After selecting a ribbon type, press the Pause key Ribbon Type SelectionStrip Wait Status Selection After selecting the Strip Wait Status, press the Pause key Kanji Code Selection Feed Key Function SelectionEuro Code Selection After selecting auto print head check, press the Pause key Auto Print Head Check SelectionCentronics Interface ACK/BUSY Timing Selection After selecting an ACK/BUSY timing, press the Pause key Media Sensor Selection Web Printer Function SelectionAfter selecting the media sensor type, press the Pause key Expansion I/O Interface Type Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Label End/Ribbon End Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key TYPE1 Reverse Feed Speed Selection Maxi Code Specification SelectionPre-Strip Selection Press the Pause key to skip 2PARAMETER SET Peel OFF TRQ R0 Strip Motor Torque SelectionStabilizer Function Selection 2PARAMETER SET Stabilizer on Printer Parameter Fine Adjustment Outline of Printer Parameter Fine Adjustment How to Enter Printer Parameter Fine Adjustment Mode 3ADJUST SET After completing the fine adjustment, press the Pause key Print Start Position Fine AdjustmentPrint Start Position Fine Adjustment Example Example of Cut Position Fine Adjustment 2 Cut/Strip Position Fine AdjustmentWhen setting +0.0 mm Prevention by fine adjustment of the cut position Operation example Issue count 3, Cut interval Example of Strip Position Fine Adjustment Reverse Feed Amount Fine Adjustment Example of Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Maximum fine adjustment value Darker Standard Lighter Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor High Standard Low 3ADJUST SET THRESHOLDR1.0V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDT1.4V Test Print Outline of Test Print Media Ribbon Save Area 8 mm How to Enter Test Print Mode4TEST Print Print Speed Setting Issue Count SettingSelect an issue count from a range of 1 to Specifying the Print Condition for the Test Print Issue Mode Selection Printing Mode SelectionSensor Type Selection Paper Feed Selection Media Length Setting4TEST Print Paper Feed Test Print Pattern Selection Slant Line 1 dot Slant Line 3 dots Print Sample of Slant Line 3 dots Print Sample of Characters CharactersBarcode Print Sample of Barcodes Print Sample of Non-print Non-PrintingFactory Test Print Sample of Factory Test Prints bar codes on 5 pieces of media Auto PrintPause key Prints characters on 5 pieces of media Sensor Adjustment Outline of the Sensor Adjustment Thermistor Status Display Black Mark Sensor AdjustmentHow to Enter the Sensor Adjustment Mode 5SENSOR ADJ Press the Pause key to return to 5SENSOR ADJ. display Feed Gap Sensor AdjustmentRibbon End Sensor Adjustment Ribbon Level 5SENSOR ADJ. Trans Outline of RAM Clear How to Enter RAM Clear ModeRAM Clear 6RAM Clear No RAM Clear Maintenance Counter ClearRAM Clear Menu Selection SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Solenoid drive time for head up Parameter ClearMode Initial values after clearing the parameters Parameter Clear 170.6 mm How to Enter IP Address Setting Mode IP Address SettingOutline of the IP Address Setting 7IP Address To enter each sub menu, press the Pause key When Printer IP Adres is displayed, press the Pause keySet the IP address using the following procedure Printer IP Adres Dhcp and Dhcp Client ID Setting Socket Port SettingTo set a socket port number, follow the procedure below Mode Ascii Dhcp Host Name SettingMode Ascii Dhcp Host Name Ascii code and Hex. code correspondence table Outline of Basic Setting Basic SettingHow to Enter Basic Setting Mode 8BASIC Basic Trace Selection Mode Basic Specification Selection ModeBasic File Browser Basic Expansion Mode Execution of Basic Program Rfid Module Setting Outline of the Rfid Module Setting Rfid Read Test How to Enter Rfid Module Setting ModeRead Test Procedure Press the Restart key or Feed key until 10RFID appears Module None Rfid Module Type SelectionModule None Module U2 Rfid Error Tag Detection Rfid Tag Type Selection Maximum Number of Rfid Issue Retries Issue Retry Maximum Number of Rfid Read Retries Cycle CNT After selecting the time-out, press the Pause key Rfid Read Retry Time-outCycle TIM Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Adjustment in positive + direction Rfid Adjustment for RetryAdjustment in negative − direction After selecting the adjustment value, press the Pause key Power Level Rfid Wireless Power Level SettingWhen AGC Threshold is displayed, press the Pause key Rfid AGC Threshold Value Rfid Module Q Value SettingQvalue When WT AGC is displayed, press the Pause key AGC Threshold for Data Write SettingWT AGC AGC Threshold Lower Limit for Retry Setting WT MIN AGC On Line Mode Symbols in the message „ LCD message and LED indication System Error Rfid Write Error „ Outline of Automatic Threshold Setting Automatic Threshold Setting„ How to Perform an Automatic Threshold Setting „ How to Perform a Reset Operation Reset Operation1RESET Dump Mode „ How to Perform a Dump Operation Receive buffer size Data in the receive buffer is printed as followsPrint Conditions Required label length „ How to Perform Basic Expansion Basic Expansion Mode5EXPAND Mode 6AUTO Calib Automatic Calibration Setting„ How to Choose an Automatic Calibration Setting 6AUTO Calib OFF On Line Mode „ How to Enable/Disable the LAN LAN Enable/Disable SettingOn Snmp on 8RTC SET Real Time Clock RTC Setting„ How to perform the Real Time Clock Setting 8RTC SET Date M 8RTC SET Time S 8RTC SET Time H8RTC SET Time M 8RTC SET LOW BATT. Check On Line Mode Download Program Installation Outline of FeaturesSystem Requirements Installation Procedure SetupSetup Disk Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load Rfid Analyze Tool System Requirement SX/SA Rfid Analyze Tool Set upSetup Disk Installation Setup Disk consists of one CD-ROM V1.5 U2 B-SX704-RFID-U2-EU/AU/US/CN-R Application FunctionsMain Menu SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the test mode This menu is not available Select the printer model Example Help MenuDisplays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 Tag Data U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box