Select the printer model | Toshiba B-SX6T, B-SX8T guide

5.RFID ANALYZE TOOL

EO13-33002

(Revision Date: Jul. 24, 2008)

5.3 Application Functions

(7)Select the printer model

Makes a choice of a printer model from Get Printer Type menu. Choose “B-SX6T/SX8T”.

NOTE: This information can be saved by a parameter save function.

(8)Select the test mode This menu is not available.

5- 11

Image 124

Toshiba B-SX6T, B-SX8T manual Select the printer model, Select the test mode This menu is not available

Contents

SX6T/SX8T Series Table of Contents Printer Parameter Fine Adjustment Test Print Program Down Load On Line ModeRfid Analyze Tool Introduction Key Operation Flow Operation Panel This is the start of the IP Address Setting menu. → Section → Section This is the start of the Basic Setting menu This is the Rfid Module Setting menu8BASIC Pause 10RFID Pause Self-diagnostic Test „ Outline of Self-diagnostic Test„ How to Enter Self-diagnostic Test Mode PRT Type Transfr Printing Mode Selection Dispensing Mode SelectionPRT Type no Tran PRT Type Direct Maintenance Counter/Parameter Settings Print Out Maintenance Checking & Print Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Descriptions of the Parameters Font ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic Print Sample Self-Diagnostic Test and Result Print OutAfter printing is completed, the display returns to 1DIAG Descriptions Alphanumeric Font ROM CheckKanji ROM Check Eeprom Check Sensor/Switch Print status description Sdram Capacity Sensor 2 Check Sensor/Thermistor Manual Threshold Check =300 GNDhms Rfid module check Results of a Rfid module check is printed Internal Serial Interface CheckDIN Print Head Element Check Press the Pause key to return to 1DIAG Parameter Setting Outline of Parameter Setting How to Enter Parameter Setting Mode Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Character Zero Selection Baud Rate SelectionAfter selecting a character zero, press the Pause key After selecting a baud rate, press the Pause key Data Length Selection Stop Bit Length SelectionAfter selecting a data length, press the Pause key After selecting a stop bit, press the Pause key Flow Control Code Selection Parity SelectionAfter selecting the parity, press the Pause key Auto Forward Wait Selection LCD Language SelectionAfter selecting a language, press the Pause key Head Up Cut Selection Ribbon Save Function Selection Control Code Selection 2PARAMETER SET Code AutoCode Auto Code ESC,LF,NUL Code Manual 2PARAMETER SET Control CODE1 1B Ribbon Type Selection Strip Wait Status SelectionAfter selecting a ribbon type, press the Pause key After selecting the Strip Wait Status, press the Pause key Kanji Code Selection Feed Key Function SelectionEuro Code Selection Auto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key Media Sensor Selection Web Printer Function SelectionAfter selecting the media sensor type, press the Pause key Expansion I/O Interface Type Selection Input Prime SelectionAfter selecting the Input Prime, press the Pause key Label End/Ribbon End Selection Plug & Play SelectionAfter selecting a Plug & Play, press the Pause key TYPE1 Maxi Code Specification Selection Pre-Strip SelectionReverse Feed Speed Selection Press the Pause key to skip Strip Motor Torque Selection Stabilizer Function Selection2PARAMETER SET Peel OFF TRQ R0 2PARAMETER SET Stabilizer on Printer Parameter Fine Adjustment Outline of Printer Parameter Fine Adjustment How to Enter Printer Parameter Fine Adjustment Mode 3ADJUST SET After completing the fine adjustment, press the Pause key Print Start Position Fine AdjustmentPrint Start Position Fine Adjustment Example Example of Cut Position Fine Adjustment 2 Cut/Strip Position Fine AdjustmentWhen setting +0.0 mm Prevention by fine adjustment of the cut position Operation example Issue count 3, Cut interval Example of Strip Position Fine Adjustment Reverse Feed Amount Fine Adjustment Example of Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Maximum fine adjustment value Darker Standard Lighter Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor High Standard Low 3ADJUST SET THRESHOLDR1.0V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDT1.4V Test Print Outline of Test Print Media Ribbon Save Area 8 mm How to Enter Test Print Mode4TEST Print Issue Count Setting Select an issue count from a range of 1 toPrint Speed Setting Specifying the Print Condition for the Test Print Issue Mode Selection Printing Mode SelectionSensor Type Selection Paper Feed Selection Media Length Setting4TEST Print Paper Feed Test Print Pattern Selection Slant Line 1 dot Slant Line 3 dots Print Sample of Slant Line 3 dots Characters BarcodePrint Sample of Characters Print Sample of Barcodes Non-Printing Factory TestPrint Sample of Non-print Print Sample of Factory Test Auto Print Pause keyPrints bar codes on 5 pieces of media Prints characters on 5 pieces of media Sensor Adjustment Outline of the Sensor Adjustment Black Mark Sensor Adjustment How to Enter the Sensor Adjustment ModeThermistor Status Display 5SENSOR ADJ Feed Gap Sensor Adjustment Ribbon End Sensor Adjustment Ribbon LevelPress the Pause key to return to 5SENSOR ADJ. display 5SENSOR ADJ. Trans How to Enter RAM Clear Mode RAM ClearOutline of RAM Clear 6RAM Clear Maintenance Counter Clear RAM Clear Menu SelectionNo RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Solenoid drive time for head up Parameter ClearMode Initial values after clearing the parameters Parameter Clear 170.6 mm IP Address Setting Outline of the IP Address SettingHow to Enter IP Address Setting Mode 7IP Address When Printer IP Adres is displayed, press the Pause key Set the IP address using the following procedureTo enter each sub menu, press the Pause key Printer IP Adres Dhcp and Dhcp Client ID Setting Socket Port SettingTo set a socket port number, follow the procedure below Dhcp Host Name Setting Mode Ascii Dhcp Host NameMode Ascii Ascii code and Hex. code correspondence table Basic Setting How to Enter Basic Setting ModeOutline of Basic Setting 8BASIC Basic Trace Selection Mode Basic Specification Selection ModeBasic File Browser Basic Expansion Mode Execution of Basic Program Rfid Module Setting Outline of the Rfid Module Setting How to Enter Rfid Module Setting Mode Read Test ProcedureRfid Read Test Press the Restart key or Feed key until 10RFID appears Module None Rfid Module Type SelectionModule None Module U2 Rfid Error Tag Detection Rfid Tag Type Selection Maximum Number of Rfid Issue Retries Issue Retry Maximum Number of Rfid Read Retries Cycle CNT After selecting the time-out, press the Pause key Rfid Read Retry Time-outCycle TIM Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Rfid Adjustment for Retry Adjustment in negative − directionAdjustment in positive + direction After selecting the adjustment value, press the Pause key Rfid Wireless Power Level Setting When AGC Threshold is displayed, press the Pause keyPower Level Rfid AGC Threshold Value Rfid Module Q Value SettingQvalue When WT AGC is displayed, press the Pause key AGC Threshold for Data Write SettingWT AGC AGC Threshold Lower Limit for Retry Setting WT MIN AGC On Line Mode Symbols in the message „ LCD message and LED indication System Error Rfid Write Error „ Outline of Automatic Threshold Setting Automatic Threshold Setting„ How to Perform an Automatic Threshold Setting „ How to Perform a Reset Operation Reset Operation1RESET Dump Mode „ How to Perform a Dump Operation Data in the receive buffer is printed as follows Print ConditionsReceive buffer size Required label length „ How to Perform Basic Expansion Basic Expansion Mode5EXPAND Mode Automatic Calibration Setting „ How to Choose an Automatic Calibration Setting6AUTO Calib 6AUTO Calib OFF On Line Mode „ How to Enable/Disable the LAN LAN Enable/Disable SettingOn Snmp on Real Time Clock RTC Setting „ How to perform the Real Time Clock Setting8RTC SET 8RTC SET Date M 8RTC SET Time H 8RTC SET Time M8RTC SET Time S 8RTC SET LOW BATT. Check On Line Mode Download Program Installation Outline of FeaturesSystem Requirements Setup Setup DiskInstallation Procedure Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load Rfid Analyze Tool System Requirement Set up Setup Disk Installation Setup Disk consists of one CD-ROMSX/SA Rfid Analyze Tool V1.5 Application Functions Main MenuU2 B-SX704-RFID-U2-EU/AU/US/CN-R SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the test mode This menu is not available Select the printer model Example Help MenuDisplays Printer Version and Rfid Module Version Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 Tag Data U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box