Manuals / Toshiba / Computer Equipment / Printer

Toshiba B-SX6T This is the start of the Basic Setting menu, This is the Rfid Module Setting menu

Models: B-SX8T B-SX6T

1 133

Download 133 pages 41.2 Kb

Page 8

2. SYSTEM MODE

EO13-33002 (Revision Date: Jul. 24, 2008)

2. SYSTEM MODE

Continued from the previous page.

<8>BASIC[PAUSE]

[FEED] [RESTART]



<9>FOR FACTORY						[PAUSE]
<9>FOR FACTORY						[PAUSE]


[FEED]			[RESTART]

<10>RFID[PAUSE]

[FEED]

This is the start of the Basic Setting menu.

→Section 2.8

This is the start of the Factory Mode menu.

This is the RFID Module Setting menu.

→Section 2.9

NOTES: 1. System Mode menu can be selected with the [RESTART] or [FEED] key.

2.Pressing the [PAUSE] key allows you to enter the sub menus of each System Mode menu. Flowcharts of each menu’s sub menus are provided on the following pages.

3.“x.x” of “DIAG. Vx.x” indicates firmware version and revision.

2- 2

Image 8

Toshiba B-SX6T, B-SX8T This is the start of the Basic Setting menu, This is the Rfid Module Setting menu, 8BASIC Pause

Contents

SX6T/SX8T Series Table of Contents Printer Parameter Fine Adjustment Test Print Rfid Analyze Tool On Line ModeProgram Down Load Introduction Key Operation Flow Operation Panel This is the start of the IP Address Setting menu. → Section → Section This is the start of the Basic Setting menu This is the Rfid Module Setting menu8BASIC Pause 10RFID Pause Self-diagnostic Test „ Outline of Self-diagnostic Test„ How to Enter Self-diagnostic Test Mode PRT Type Transfr Printing Mode Selection Dispensing Mode SelectionPRT Type no Tran PRT Type Direct Maintenance Counter/Parameter Settings Print Out Maintenance Checking & Print Stabilizer Auto Calib OFF LAN On Snmp on Prtr IP Address Descriptions of the Maintenance Counter Descriptions of the Parameters Font ¶¶-¶¶-¶¶-¶¶-¶¶-¶¶ Basic After printing is completed, the display returns to 1DIAG Self-Diagnostic Test and Result Print OutPrint Sample Descriptions Alphanumeric Font ROM CheckKanji ROM Check Eeprom Check Sensor/Switch Print status description Sdram Capacity Sensor 2 Check Sensor/Thermistor Manual Threshold Check =300 GNDhms DIN Internal Serial Interface CheckRfid module check Results of a Rfid module check is printed Print Head Element Check Press the Pause key to return to 1DIAG Parameter Setting Outline of Parameter Setting How to Enter Parameter Setting Mode Character Code SelectionUse the Feed or Restart key to select a desired option After selecting a character code, press the Pause key Character Zero Selection Baud Rate SelectionAfter selecting a character zero, press the Pause key After selecting a baud rate, press the Pause key Data Length Selection Stop Bit Length SelectionAfter selecting a data length, press the Pause key After selecting a stop bit, press the Pause key After selecting the parity, press the Pause key Parity SelectionFlow Control Code Selection After selecting a language, press the Pause key LCD Language SelectionAuto Forward Wait Selection Head Up Cut Selection Ribbon Save Function Selection Control Code Selection 2PARAMETER SET Code AutoCode Auto Code ESC,LF,NUL Code Manual 2PARAMETER SET Control CODE1 1B Ribbon Type Selection Strip Wait Status SelectionAfter selecting a ribbon type, press the Pause key After selecting the Strip Wait Status, press the Pause key Euro Code Selection Feed Key Function SelectionKanji Code Selection Auto Print Head Check Selection Centronics Interface ACK/BUSY Timing SelectionAfter selecting auto print head check, press the Pause key After selecting an ACK/BUSY timing, press the Pause key After selecting the media sensor type, press the Pause key Web Printer Function SelectionMedia Sensor Selection After selecting the Input Prime, press the Pause key Input Prime SelectionExpansion I/O Interface Type Selection After selecting a Plug & Play, press the Pause key Plug & Play SelectionLabel End/Ribbon End Selection TYPE1 Maxi Code Specification Selection Pre-Strip SelectionReverse Feed Speed Selection Press the Pause key to skip Strip Motor Torque Selection Stabilizer Function Selection2PARAMETER SET Peel OFF TRQ R0 2PARAMETER SET Stabilizer on Printer Parameter Fine Adjustment Outline of Printer Parameter Fine Adjustment How to Enter Printer Parameter Fine Adjustment Mode 3ADJUST SET Print Start Position Fine Adjustment Example Print Start Position Fine AdjustmentAfter completing the fine adjustment, press the Pause key When setting +0.0 mm 2 Cut/Strip Position Fine AdjustmentExample of Cut Position Fine Adjustment Prevention by fine adjustment of the cut position Operation example Issue count 3, Cut interval Example of Strip Position Fine Adjustment Reverse Feed Amount Fine Adjustment Example of Reverse Feed Amount Fine Adjustment Coordinate Fine Adjustment Example of X Coordinate Fine Adjustment Maximum fine adjustment value Darker Standard Lighter Ribbon Motor Voltage Fine Adjustment Feed/Take-up Motor High Standard Low 3ADJUST SET THRESHOLDT1.4V Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor3ADJUST SET THRESHOLDR1.0V Test Print Outline of Test Print 4TEST Print How to Enter Test Print ModeMedia Ribbon Save Area 8 mm Issue Count Setting Select an issue count from a range of 1 toPrint Speed Setting Specifying the Print Condition for the Test Print Sensor Type Selection Printing Mode SelectionIssue Mode Selection 4TEST Print Paper Feed Media Length SettingPaper Feed Selection Test Print Pattern Selection Slant Line 1 dot Slant Line 3 dots Print Sample of Slant Line 3 dots Characters BarcodePrint Sample of Characters Print Sample of Barcodes Non-Printing Factory TestPrint Sample of Non-print Print Sample of Factory Test Auto Print Pause keyPrints bar codes on 5 pieces of media Prints characters on 5 pieces of media Sensor Adjustment Outline of the Sensor Adjustment Black Mark Sensor Adjustment How to Enter the Sensor Adjustment ModeThermistor Status Display 5SENSOR ADJ Feed Gap Sensor Adjustment Ribbon End Sensor Adjustment Ribbon LevelPress the Pause key to return to 5SENSOR ADJ. display 5SENSOR ADJ. Trans How to Enter RAM Clear Mode RAM ClearOutline of RAM Clear 6RAM Clear Maintenance Counter Clear RAM Clear Menu SelectionNo RAM Clear SX6T-TS12-QM-R and B-SX8T-TS12-QM-R V1.0B or earlier Mode Parameter ClearSolenoid drive time for head up Initial values after clearing the parameters Parameter Clear 170.6 mm IP Address Setting Outline of the IP Address SettingHow to Enter IP Address Setting Mode 7IP Address When Printer IP Adres is displayed, press the Pause key Set the IP address using the following procedureTo enter each sub menu, press the Pause key Printer IP Adres To set a socket port number, follow the procedure below Socket Port SettingDhcp and Dhcp Client ID Setting Dhcp Host Name Setting Mode Ascii Dhcp Host NameMode Ascii Ascii code and Hex. code correspondence table Basic Setting How to Enter Basic Setting ModeOutline of Basic Setting 8BASIC Basic File Browser Basic Specification Selection ModeBasic Trace Selection Mode Basic Expansion Mode Execution of Basic Program Rfid Module Setting Outline of the Rfid Module Setting How to Enter Rfid Module Setting Mode Read Test ProcedureRfid Read Test Press the Restart key or Feed key until 10RFID appears Module None Module U2 Rfid Module Type SelectionModule None Rfid Error Tag Detection Rfid Tag Type Selection Maximum Number of Rfid Issue Retries Issue Retry Maximum Number of Rfid Read Retries Cycle CNT Cycle TIM Rfid Read Retry Time-outAfter selecting the time-out, press the Pause key Maximum Number of Rfid Write Retries Rfid Write Retry Time-out Rfid Adjustment for Retry Adjustment in negative − directionAdjustment in positive + direction After selecting the adjustment value, press the Pause key Rfid Wireless Power Level Setting When AGC Threshold is displayed, press the Pause keyPower Level Rfid AGC Threshold Qvalue Rfid Module Q Value SettingValue WT AGC AGC Threshold for Data Write SettingWhen WT AGC is displayed, press the Pause key AGC Threshold Lower Limit for Retry Setting WT MIN AGC On Line Mode Symbols in the message „ LCD message and LED indication System Error Rfid Write Error „ How to Perform an Automatic Threshold Setting Automatic Threshold Setting„ Outline of Automatic Threshold Setting 1RESET Reset Operation„ How to Perform a Reset Operation Dump Mode „ How to Perform a Dump Operation Data in the receive buffer is printed as follows Print ConditionsReceive buffer size Required label length 5EXPAND Mode Basic Expansion Mode„ How to Perform Basic Expansion Automatic Calibration Setting „ How to Choose an Automatic Calibration Setting6AUTO Calib 6AUTO Calib OFF On Line Mode On Snmp on LAN Enable/Disable Setting„ How to Enable/Disable the LAN Real Time Clock RTC Setting „ How to perform the Real Time Clock Setting8RTC SET 8RTC SET Date M 8RTC SET Time H 8RTC SET Time M8RTC SET Time S 8RTC SET LOW BATT. Check On Line Mode System Requirements Outline of FeaturesDownload Program Installation Setup Setup DiskInstallation Procedure Before starting the download procedure First, start the printer in download mode EO13-33002 Program Down Load Program Down Load Program Down Load Rfid Analyze Tool System Requirement Set up Setup Disk Installation Setup Disk consists of one CD-ROMSX/SA Rfid Analyze Tool V1.5 Application Functions Main MenuU2 B-SX704-RFID-U2-EU/AU/US/CN-R SX708-RFID-U2-EU/CN-R File Menu EO13-33002 End Exit Exits from the Analyze Tool program Tool Menu NON, XON, XON/XOFF PWR Level Change AGC Read Value Sheet Setting Makes settings for the media to be used Select the test mode This menu is not available Select the printer model Displays Printer Version and Rfid Module Version Help MenuExample Operating Procedure Click on the Tool menu, and choose CommSetting RTS/CTS+XON/XOFF SX704-RFID-U2-EU/AU/US/CN-R U2 Tag Data U2 B-SA704-RFID-U2-EU/AU/US/CN-R B-SX708-RFID-U2-EU/CN-R EO13-33002 Revision Date Jul Operatin Procedure Write/Read Results Box When U2 is selected Write/Read Results Box