Sears 917.258552 7ro Start Engine See Fig, Purge Transmission, Hydrostatic Transmission Warm UP

Page 14

O ERATION

7ro START ENGINE (See Fig. 9)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuet from the tank to the engine.

,Be sure freewheet cdntrol is in the transmission em gaged position.

Sit on seat in operating position_ depress clutch/brake pedal and set parking brake.

o Place motion control lever in neutral (N) position.

oMove attachment c_utch to "DISENGAGED" position. o Move throttle control to choke (i_,l) position.

[dote: Before starting, read the warm and cold starting procedures below.

oInsert key into ignition and turn key clockwise to"START" position and release key as soon as engine starts. Do not run starter continuously for more than fifteen sec- onds per minute, If the engine does not start after several attempts, move throttle control to fast (,_) position_ wait a few minutes and try again, tf engine still does not start, move the throttle control back to the choke (1\1)position and retry.

WARM WEATHER STARTING (50° F and above)

When engine starts, move the throttle controlto the fast

(@)position_

•The attachments and ground drive can now be used, if the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, ailow engine to run with the throttle control in the choke (fXI) position until the engine runs roughly, then move throttle control to fast (,€_) position. This may require an engine warrn-up period from several seconds to several minutes, depending on the temperature.

HYDROSTATIC TRANSMISSION WARM UP

Before driving the unit in cold weather, the transmis- sion should be warmed up as follows:

•Be sure the tractor is on leVel ground.

. Place the motion control lever in neutral. Release the parking brake and let the clutch/brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

The attachments canalso be used during the engine warm-up period after the transmission has been warmed up.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See "TO ADJUST CARBURETOR" in the Service and Adjustments section of this manual,

PURGE TRANSMISSION

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air Jnside the transmission which may have devel- oped during shipping of your tractol °.

IMPORTAN3"," SHOULD YOUR TRANSMISSION REQUIRE

REMOVAL FOR SERVICE OR REPLACEMENT, 1T

SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

"Place tractor safely on level surface with engine off and parking brake set.

*Disengage transmission by placing freewheel control in freewheeling position (See "TO TRANSPORT" in this section of manual).

=Sitting in the tractor seat, start engine. After theengine is running, move throttle controt to stow (,_i_) position. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

. Move motion control lever to rut! forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times,

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

Move motion controt lever to neutral (N) position. Shut- off engine and set parking brake.

Engage transmission by placing freewheel control in driving position (See "TO TRANSPORT" in this section of manua!).

,Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

,Slowly move motion control lever forward, after'the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the tractor moves approximately five (5) feet return the motion control iever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

,Your tractor is now purged and now ready for normal operation.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents AFTZ Safety Rules II. Slope OperationLimited 90 DAY Warranty on Battery Maintenance AgreementLimited TWO Year Warranty on Craftsman Riding Equipment ModelIndex Engine PerformanceContents of Hardware Pack ASS LY Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonCheck Deck Levelness AssemblyInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigDschargng Checklis TTo Convert to Bagging or Lock Battery Reverse ForwardSlow Operation Know Your TractorStopping See Fig HOW to USE Your TractorTo SET Parking Brake See Fig ADD Gasoline Before Startwng the EngineTo Operate on Hills Hydrostatic Transmission Warm UP 7ro Start Engine See FigPurge Transmission ERAT!ON Mulching Mowng TipsGeneral Recommendations Maintenance ScheduleChart LUBRJCATmONBrake Operation BatteryTractor TiresTR Filter See Fig. t6 EngineTransaxle Pump Fluid Spark Plugs CleaningMuffler OFF To iNSTALL Mower See Fig, !9To Remove Mower See Fig To Level Mower Housing To Replace Motion Drive Belt To Adjust Brake See FigTo Replace Mower Blade Drive Belt See FigTo Adjust Steering Wheel Alignment Service AN Adjustm NTSTo Adjust Motion Control Lever Front Wheel TOE-INtCAMBERTo Remove Hood and Grill Assembly Service a AdjustmentsTo Start Engjne WiTH a Weak Battery See Fig To Replace Headlight BulbEngine To Adjust Throttle Control CableTo Adjust Carburetor See Fig Fuelsystem StorageOther Engine OILPoints TroubleshootingProblemcause CorrectionCorrectbon ClutchTractor = Model Number Tractor - Model Number ElectricalPart Description Tractor Model NumberKEY Chassis and Enclosures KEY Part NO. noRepair pARTSTRACTORtooELNUMBER97..258552 STL DriveDESCRePTON Steering Assembly Tractor -- Model NumberTRACTOR-- Model Number KEY Part NO. noDescription Seat AssemblyTractor Model Number 917,258552 KEY Part DescriptionKEY Part NO. no TRACTOR--MODELWheels & Tires Engine Optional Equipment Engine NO. NO.DESCRiPTiON150 \ Tractor - Model Number 917,258552Mower Lift 426 161718NO. NO. DESCRIPTtON Tractor =- Model NumberKEY Part Locknut, Hex106 Mower Deck105 Part Mower DeckKEY DESCRmPTIONTractor == Model Number 917,258552 Hydro Gear Transaxle Model NumberRetaining Hydro Gear Transaxle Model Number 310=0650NO. no Description 142951Tractor Model Number Crankshaft KEY Part Tractor - Model Number 917Kohler Engine -- Model Number CV15S, Type Number PS-41526 Not Illustrated KEY Part2227 Tractor --MODEL Number 917,258552Fuel System Cylinder HEAD, Valve and Breather Kohler Engine -MODEL Number CV15S, Type Number PB-41526Fuel System KEY Part NO. no DescriponStartn Tractor = Model Number 917,258552Kohler Engine Model Number CV15S Type Number PS-41526 Crankcase KEY Part Kohler Engine -- Model Number CV!5S, Type Number PS-41526Electrical Starting System KEY Part NO. noService Notes Suggested Guide for Sighting Slopes for Safe Operation If YOU Need Repair Service Or PartsFor Repair SERVICE, Call this Toll Free Number Orconsumer Assistance HOT LINE, Call this Toll Free Number

917.258552 specifications

The Sears 917.258552 is a standout model in the lineup of lawn tractors offered by Sears. This versatile machine combines robust features and innovative technologies to provide homeowners with an efficient and effective solution for lawn maintenance.

One of the main features of the Sears 917.258552 is its powerful engine. Powered by a reliable 18.5 horsepower Briggs & Stratton engine, this lawn tractor is capable of tackling various lawn sizes and types. The engine's performance is enhanced by a smooth automatic transmission, which allows for easy speed adjustments on the go, ensuring that users can navigate their yards with ease and precision.

The cutting deck of the Sears 917.258552 measures a generous 42 inches, making it suitable for larger areas without sacrificing maneuverability. The deck design incorporates a durable steel construction, providing longevity and resilience against the rigors of regular lawn care. Additionally, it features a deck wash system, allowing users to clean the underside of the deck efficiently and maintain optimal cutting performance over time.

Another noteworthy technology included in this model is the cutting height adjustment feature. The Sears 917.258552 provides multiple cutting height settings, which can be easily adjusted to achieve the desired grass height. This flexibility allows users to manage their lawns' aesthetics while promoting healthy grass growth.

The tractor's ergonomics are designed with user comfort in mind. The high-back seat provides ample support during extended periods of operation, while the easy-to-reach controls facilitate a hassle-free mowing experience. With a tight turning radius, the Sears 917.258552 can navigate around obstacles effectively, making it an ideal choice for complex landscapes.

Moreover, this tractor is designed for storage and maintenance convenience. It features a compact design that simplifies storage, while the intuitive layout allows for easy maintenance access to key components, such as the battery and fuel system.

In summary, the Sears 917.258552 lawn tractor is an exceptional choice for homeowners looking for a reliable and efficient lawn care solution. With its powerful engine, durable cutting deck, adjustable cutting heights, ergonomic design, and ease of maintenance, this model epitomizes the blend of performance and user-friendly features that Sears aims to deliver in their lawn maintenance products. Whether for residential lawns or larger garden plots, the Sears 917.258552 is equipped to handle the task with efficiency and ease.
Top Page Image Contents