Sears 316.2927 manual Air Filter Maintenance, Carburetor Adjustment, Replacing The Spark Plug

Page 10

•When adding oil, the unit must be laid back in the horizontal position on a flat surface with the upper handle touching the ground.

See Figure 8.

•Refill the crankcase with 3.4 fl.oz. (100 ml.) of SAE 30 SF, SG, or SH oil.

•Replace the oil fill plug/dipstick.

Air Filter Maintenance

•Open the air filter cover on side of engine by pushing the tab on the left side in and swinging the air filter cover out and off. See Figure 10.

•Remove the air filter and screen.

•Wash the filter in detergent and water. Rinse the filter thoroughly and allow it to dry.

•Apply enough clean SAE 30 motor oil to lightly coat the filter and squeeze the filter to spread and remove excess oil.

•Replace the screen and filter.

•Position the hooks on the right side of the air filter cover into the slots at the right side of the air filter housing.

•Swing the cover to the left until the tab on the air filter cover snaps into place in the slot.

Air Filter

Air Filter

Housing

 

 

Air Filter Cover

Screen

 

Air Filter

 

 

Tab

Figure 10

Carburetor Adjustment

If the engine will not idle, hesitates or stalls on acceleration, or there is a loss of engine power have the carburetor adjusted by an Sears service center.

Replacing The Spark Plug

The spark plug should be removed and check after every 25 hours of operation. To replace the spark plug proceed as follows:

•Stop the engine and allow it to cool. Grasp the plug wire firmly and pull the cap from the spark plug.

•Clean dirt from around the spark plug and remove the spark plug from the cylinder head by turning counterclockwise using a socket.

•Set the air gap at 0.025 in (0.655 mm.) using a feeler gauge. See Figure 11.

•Install a correctly gapped spark plug in the cylinder head and tighten by turning the socket clockwise until snug. Do not over tighten.

.025" Feeler Gauge

Spark Plug

Figure 11

Spark Arrestor Maintenance

•Remove the muffler cover, if equipped, by pressing down on the corner with a flat blade screwdriver. Slide the notches on the sides of the muffler cover over the tabs on the engine cover and remove.

•Remove the screw attaching the spark arrestor cover to the muffler. See Figure 12.

 

Spark Arrestor

Muffler

Screen

Screw

 

 

 

 

Tab

 

Slot

Spark Arrester

 

 

Cover

Figure 12

•Pull the tab on the spark arrestor cover out of the muffler and remove the spark arrestor cover.

•Remove the spark arrestor screen from the spark arrestor cover.

•Clean the spark arrestor screen with a wire brush or replace screen.

•Reinstall the spark arrester screen, spark arrestor cover, and screw.

Rocker Arm Clearance

This requires disassembly of the engine. If you feel unsure or unqualified to perform this adjustment, take the unit to a Sears service center.

NOTE: Inspect the valve to rocker arm clearance with a feeler gauge after the first 10 hours of operation

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Cultivator / Edger Table of Contents WarrantySafety TrainingMaintenance And Storage Assembly Disconnecting Spark PlugSetting Up Your Cultivator / Edger Removing Unit From CartonStopping Engine OperationGas Fill-Up Oil Fill-UpStarting Engine Attaching the Edger Wheel And Blade Using Your CultivatorAdjusting the Wheel Support Bracket Starting a Warm EngineChecking Oil MaintenanceChanging Oil Spark Arrestor Maintenance Air Filter MaintenanceCarburetor Adjustment Replacing The Spark PlugIts travel. Make sure Storing Your Cultivator / Edger Tine Removal and ReplacementService and Storage EngineTroubleshooting Problem Cause RemedyParts List Part Description 5045 9570 Short Block 5-13, 15, 16, 71-83 Owner’s Warranty Responsibilities Emission Warranty StatementManufacturer’s Warranty Coverage Garantía ÍndiceEsta garantía no cubre Capacitación SeguridadFuncionamiento Mantenimiento y almacenamientoLas responsabilidades De la garantía del Dueño Como Declaración de Garantía de EmisiónCalifornia / la emisión de Ministerio DEL Medio La cobertura De la garantía del FabricanteDesconexión De La Bujía Configuración de su cultivadora / bordeadoraParties Lâches dans Carton MontajeFuncionamiento Llenado de nafta Detención del motorLlenado de aceite Encendido del motorAjuste de la ménsula de soporte de la rueda Utilización de su cultivadoraArranque de un motor en caliente Conexión de la rueda y de la cuchilla de la bordeadora Cambio de aceite MantenimientoReemplazo de la bujía Mantenimiento del filtro de aireAjuste del carburador Mantenimiento del dispositivo contra chispasDespacho de aduana de Balancín 003-.006 .076-.152mm Servicio Y Almacenamiento Almacenamiento de la cultivadora / bordeadoraMotor Solución DE Problemas Problema Causa SoluciónPage Page Get it fixed, at your home or ours

316.2927 specifications

The Sears 316.2927 is a versatile electronic keyboard that gained popularity in the 1980s for its compact design and user-friendly features. This model epitomized a blend of affordability and functionality, making it an attractive choice for both novice musicians and those seeking a portable instrument.

One of the main features of the Sears 316.2927 is its 49-key layout. The keys are not full-sized, which contributes to the keyboard's lightweight nature and portability. This design allows users to play a range of musical styles while still being easy to transport from one location to another. The keyboard also includes a number of built-in sounds, allowing users to explore various instruments, including pianos, organs, and synthesizers. The variety of sounds can inspire creativity and provide a richer music-making experience.

The Sears 316.2927 incorporates several essential technologies that were innovative for its time. It includes an integrated rhythm section, which features a selection of percussion patterns that can enhance any performance. Users can choose from multiple styles, such as rock, jazz, and disco, offering a range of backgrounds for their music. This rhythm feature is coupled with adjustable tempo controls, allowing players to set their preferred speed and tailor the backing track to suit their needs.

In terms of characteristics, this model boasts a straightforward interface, with easily accessible buttons and knobs for sound selection, volume control, and rhythm settings. The LCD display provides essential feedback, guiding users through various functions and settings. The keyboard is powered by batteries or can be connected to a standard power outlet, making it versatile for both home use and on-the-go sessions.

Another notable characteristic of the Sears 316.2927 is its ability to connect to external audio devices. The inclusion of line-out and headphone jacks enables users to connect the keyboard to amplifiers or recording equipment, expanding its use in live performances and studio settings. This connectivity enhances the instrument's utility, allowing it to fit seamlessly into a variety of musical environments.

Overall, the Sears 316.2927 is a well-rounded electronic keyboard that balances portability, user-friendly features, and a range of sounds. Its combination of built-in rhythms, easy interface, and connectivity options makes it an excellent choice for budding musicians and seasoned players alike, providing a platform for creativity and musical exploration.
Top Page Image Contents