McCulloch 532 43 45-03, 96041017700 manual Install Seat See Fig, Check Brake System

✓ Be sure brake system is in safe operating condition.

✓ Be sure Operator Presence System and Reverse Op- eration System (ROS) are working properly (See the Operation and Maintenance sections in this manual).

function. Operate them before you start the engine.

Become familiar with all controls, their location and

(Tires must be

and wires are properly clamped.

WHILE LEARNING HOW TO USE YOUR TRACTOR, PAY EXTRA ATTENTION TO THE FOLLOWING IMPORTANT ITEMS:

✓ Engine oil is at proper level.

✓ Fuel tank is filled with fresh, clean, regular unleaded

Check wiring. See that all connections are still secure

✓

Check mower and drive belts. Be sure they are routed properly around pulleys and inside all belt keepers.

✓

front-to-rear for best cutting results. properly inflated for leveling).

the tires were overinflated at the factory).

✓ Be sure mower deck is properly leveled side-to-side/

All tires are properly inflated. (For shipping purposes,

Seat is adjusted comfortably and tightened securely.

No remaining loose parts in carton.

✓ All assembly instructions have been completed.

✓

✓ Battery is properly prepared and charged.

✓

✓

✓CHECKLIST

BEFORE YOU OPERATE YOUR NEW TRACTOR, WE WISH TO ASSURE THAT YOU RECEIVE THE BEST PERFORMANCE AND SATISFACTION FROM THIS QUALITY PRODUCT.

PLEASE REVIEW THE FOLLOWING CHECKLIST:

After you learn how to operate your tractor, check to see that the brake is operating properly. See “TO CHECK BRAKE” in the Service and Adjustments section of this manual.

See the figures that are shown for replacing motion and mower blade drive belts in the Service and Adjustments sec- tion of this manual. Verify that the belts are routed correctly.

CHECK FOR POSITION OF ALL BELTS

For best cutting results, mower housing should be properly leveled. See “TO LEVEL MOWER” in the Service and Adjustments section of this manual.

CHECK DECK LEVELNESS

Reduce tire pressure to PSI shown on tires.

•

CHECK TIRE PRESSURE

The tires on your tractor were overinflated at the factory for shipping purposes. Correct tire pressure is important for best cutting performance.

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly

of seat to tractor.

• Pivot seat upward and remove from the cardboard pack-

ing. Remove the cardboard packing and discard.

• Place seat on seat pan so head of shoulder bolts are

positioned over the large slotted holes in pan.
• Push down on seat to engage shoulder bolts in slots
and pull seat towards rear of tractor.
• Pivot seat and pan forward and assemble adjustment
knob and flat washer loosely. Do not tighten.
• Lower seat into operating position and sit in seat.
• Slide seat until a comfortable position is reached which	CHECK BRAKE SYSTEM
allows you to press clutch/brake pedal all the way
down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SHOULDER

BOLTS

SEAT

PAN

WASHER

02617

ADJUSTMENT

KNOB

02615

Fig. 3

NOTE: You may now roll your tractor off the skid. Follow the instructions below to remove the tractor from the skid.

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

TO ROLL TRACTOR OFF SKID (See Operation section for location and function of controls)

•Raise attachment lift lever to its highest position.

•	Releaseparkingbrakebydepressingclutch/brakepedal.	gasoline.
		✓
•	Place gearshift lever in neutral (N) position.

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against tractor.

Continue with the instructions that follow.

7