McCulloch MC16H38ST, 96011013201 Tools Required for Assembly, To Remove Tractor from CAR- TON

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrench

Pliers

(2)

9/16" wrenches

Tire pressure gauge

 

 

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CAR- TON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING

BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. MC16H38ST 16.0 HP 38 Inch Lawn Tractor General Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationService III. ChildrenIV. Towing Table of Contents Battery Unassembled PartsTo Remove Tractor from CAR- TON AssemblyTools Required for Assembly Before Removing Tractor from SkidConnect Battery See Figs Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills Before Starting the EngineTo Operate Mower See Fig To Transport See FigsPurge Transmission ADD GasolineTo Start Engine See Fig Automatic Transmission Warm UPMowing Tips Service Dates MaintenanceLubrication Chart General RecommendationsTires TractorBrake Operation Operator Presence SystemEngine Cleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake To Replace Motion Drive Belt See FigTo Check Brake To Adjust Steering Wheel ALIGN- Ment Transaxle Motion Control Lever Neutral Adjustment See FigTransmission REMOVAL/REPLACEMENT Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points With attachment clutch Schematic Tractor - Model Number MC16H38ST 96011013201, Product no 11Electrical KEY Part NO. NO. Description Chassis Repair Parts Drive Repair Parts Steering Repair Parts Engine Optional EquipmentSeat Decals Wheels & TiresMower Lift Mower Deck KEY Part Description Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

96011013201, MC16H38ST specifications

The McCulloch 96011013201, also known as the MC16H38ST, is a remarkable addition to the lineup of McCulloch outdoor power equipment. This versatile and highly efficient string trimmer is designed to provide users with exceptional performance for landscaping and gardening tasks.

One of the standout features of the MC16H38ST is its powerful 38cc 2-stroke engine, which promises not only brute strength but also efficient fuel consumption. This engine allows for a robust cutting performance, making it ideal for tackling tough weeds and thick grass. The advanced engine technology ensures reliable starting and smooth operation, reducing the frustration often associated with starting outdoor equipment.

This model is equipped with a split shaft design, providing ease of use and enhanced versatility. Users can effortlessly switch attachments, transforming the trimmer into a multi-functional tool for various gardening tasks. Whether you need to edge your lawn, trim hedges, or even tackle tough underbrush, the MC16H38ST can adapt to your needs with ease.

Comfort and ergonomics are key considerations in the design of the MC16H38ST. The trimmer features an adjustable handle, allowing users to find their ideal working position. The lightweight design further enhances maneuverability, reducing fatigue during extended use. Additionally, the anti-vibration technology incorporated into the handle system helps minimize user discomfort, enabling longer, more productive work sessions.

The McCulloch 96011013201 also boasts a reliable automatic line feed system, which automatically dispenses the cutting line as needed during operation. This feature not only saves time but also ensures a consistently clean cut, contributing to the overall efficiency of your gardening efforts.

For enhanced visibility during low-light conditions, the trimmer is designed with a durable cutting head that allows for precise trimming in tight spaces. Its robust design and construction ensure longevity, making it a worthy investment for both amateur gardeners and professional landscapers.

In summary, the McCulloch 96011013201, MC16H38ST, is a well-engineered, feature-rich string trimmer that marries power, versatility, and comfort. With its potent engine, split shaft design, adjustable ergonomics, and automatic line feed system, it delivers outstanding performance, making it an invaluable tool for maintaining beautiful lawns and gardens. Whether you are a weekend warrior or a professional gardener, the MC16H38ST is sure to impress with its performance and reliability.
Top Page Image Contents