Troy-Bilt TB4000 manual Stopping Instructions, Engine Re-Start Warm Engine With Fuel

Page 15

Operation (continued)

Stop/Off (O)

 

 

On/Off Stop

 

 

Control

Fig. 5-1

 

Start/On (I)

 

 

PARTIAL (B)

RUN (C)

Primer Bulb

FULL

 

 

Choke (A)

 

 

Choke

 

 

Lever

 

 

Fig. 5-2

 

 

5.Fully press and release the primer bulb slowly 5 to 7 times. Gasoline should be felt and visible in the bulb (Fig. 5-2). If gasoline has not entered the bulb, press three more times, or until it does.

6.Squeeze the throttle control to the wide open (full throttle) position.

7.With the unit in the starting position (Fig. 5-3) pull

the starter rope briskly 5 times in the FULL choke (A) position. If the engine attempts to run before the fifth pull, proceed to step 8.

8.Move the choke lever to the PARTIAL (B) position (Fig. 5-2).

NOTE: The engine will not run in the FULL choke

(A) position.

9.Pull the starter rope 1 to 3 pulls until the engine starts. Run for 15-30 seconds. If the unit fails to start return to step 7.

10.Move the choke lever to the RUN (C) position and run at full throttle for 30 seconds.

11.Release the throttle control to the idle position and begin operation.

NOTE: f the engine does not start using these procedures, repeat steps 5 through 11 using TWO

(2) pulls in the FULL choke (A) position.

Starter

Rope

Fig. 5-3

Throttle

Control

 

 

Engine Re-Start - Warm Engine With Fuel

1.Put the On/Off Stop Control in the START [I] position (Fig. 5-1).

2.Move the choke lever to the PARTIAL (B) position (Fig. 5-2).

3.Squeeze the throttle control to the wide open (full throttle) position.

4.With the unit in the starting position (Fig. 5-3), pull the starter rope briskly until the engine starts.

5.When the engine starts, move the choke lever to

the RUN (C) position, and run at full throttle for 30 seconds.

NOTE: If the engine does not start using the Engine Re-start procedures, revert to the Cold Start procedures.

NOTE: 4-stroke engines, like cars, are able to start in the idle position. As an alternate method, you may want to start your unit in the idle position when the unit is warm. With the On/Off Stop Control in the START position and the choke lever in the RUN (C) position, pull the starter rope briskly. When the engine starts, run at full throttle for 30 seconds. If the unit fails to start or dies, revert to the Engine Re-Start procedure.

STOPPING INSTRUCTIONS

1.Release your hand from the throttle control (Fig. 5-3). Allow the engine to idle.

2.To stop the engine, put the On/Off Stop Control in the STOP [O] position (Fig. 5-1).

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Owner/Operator Manual Cycle Trimmer Brush Cutter Introduction Table of ContentsAccessory 182153 Spark Arrestor Kit Service InformationBefore Operating SafetySymbol Meaning Safety Warnings for GAS TrimmersWhile Operating with Cutting Blade While OperatingFor Service INFORMATION, Call Safety and International SymbolsOther Safety Warnings Symbol Meaning Safety Alert SymbolThrown Objects and Rotating Cutter can Cause Severe Injury Symbol Meaning Unleaded FuelTRIMMER/BRUSH Cutter Safety OILApplications Know Your UnitAdjusting AssemblyInstalling and Adjusting the J-HANDLE InstallingRemove the Cutting Attachment Shield Installing the HarnessRemoving and Installing Cutting Attachment Shield Remove the Cutting Attachment and Install the Cutting BladeRemove the Cutting Attachment Install the Cutting Attachment Remove the Cutting Blade and Install the Cutting AttachmentOil and Fuel Recommended OIL TypeRecommended Fuel Type Operation Fueling UnitStarting Instructions Engine Re-Start Warm Engine With Fuel Stopping InstructionsAdjusting Trimming Line Length Holding the TrimmerTips for Best Trimming Results Using the Cutting Blade Decorative TrimmingCutting Blade Operating Tips Line Installation MaintenanceMaintenance Schedule When Maintenance Needed GO toGo To for Membrane Line Installation Single Line InstallationChanging the OIL Installing a Prewound ReelReplacement Parts Checking the OIL LevelCleaning the Air Filter AIR Filter MaintenanceCheck Fuel Carburetor AdjustmentOil and Fuel, Recommended Fuel Clean Air Filter Rocker ARM ClearanceReplacing the Spark Plug Long Term Storage ACCESSORIES/REPLACEMENT PartsCleaning StorageU S E T I O N TroubleshootingSpecifications 200-10,000 rpmInch 0.655 mm Warranty Owners Warranty ResponsibilitiesManufacturers Warranty Coverage MTD Southwest Inc

TB4000 specifications

The Troy-Bilt TB4000 is a versatile and reliable workhorse designed for homeowners and landscapers alike. This compact tiller blends power, efficiency, and user-friendly features, making it an indispensable tool for garden enthusiasts looking to cultivate and maintain their soil.

One of the standout features of the TB4000 is its robust engine. Equipped with a 4-cycle, 24.5cc engine, it delivers ample power to tackle tough soil conditions. This engine provides reliable performance while being easy to start thanks to its user-friendly recoil start mechanism. The four-stroke design eliminates the need for mixing fuel and oil, simplifying maintenance.

The TB4000 boasts a unique tilling capability that makes it suitable for a variety of gardening tasks. It features a 12-inch tilling width and adjustable tilling depth, allowing users to customize their tilling experience. Whether preparing a new garden bed or cultivating existing soil, the TB4000 can handle it with ease.

Durability is another important aspect of the TB4000's design. Its heavy-duty steel tines are built to withstand rigorous use and ensure longevity. The tiller is equipped with a front-mounted transport wheel, which makes it easy to maneuver from one location to another without straining the back or arms.

User comfort is also a major consideration in the design of the TB4000. The tiller features an ergonomic handle that can be adjusted for height, reducing strain during operation. Additionally, its lightweight design aids in overall control and ease of use.

For added convenience, the TB4000 offers a variety of tilling settings. It includes a forward-rotating tine mechanism, ideal for breaking up hard soil, while its adjustable speed allows for fine-tuning based on the task.

In terms of technology, the Troy-Bilt TB4000 comes equipped with enhancements that optimize performance. Its air filter system ensures that the engine runs smoothly by keeping dirt and debris at bay, which can be particularly useful in dusty conditions.

Overall, the Troy-Bilt TB4000 stands out in the realm of tillers, providing exceptional performance, durability, and user comfort. Whether you are new to gardening or a seasoned pro, this tiller is designed to meet the demands of various gardening tasks, making it an excellent investment for anyone dedicated to cultivating lush and healthy landscapes.
Top Page Image Contents